/* ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.apache.org/licenses/LICENSE-2.0 Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License. */ /** * @file STM32F4xx/hal_lld.c * @brief STM32F4xx/STM32F2xx HAL subsystem low level driver source. * * @addtogroup HAL * @{ */ /* TODO: LSEBYP like in F3.*/ #include "ch.h" #include "hal.h" /*===========================================================================*/ /* Driver local definitions. */ /*===========================================================================*/ /*===========================================================================*/ /* Driver exported variables. */ /*===========================================================================*/ /*===========================================================================*/ /* Driver local variables and types. */ /*===========================================================================*/ /*===========================================================================*/ /* Driver local functions. */ /*===========================================================================*/ /** * @brief Initializes the backup domain. * @note WARNING! Changing clock source impossible without resetting * of the whole BKP domain. */ static void hal_lld_backup_domain_init(void) { /* Backup domain access enabled and left open.*/ PWR->CR |= PWR_CR_DBP; /* Reset BKP domain if different clock source selected.*/ if ((RCC->BDCR & STM32_RTCSEL_MASK) != STM32_RTCSEL) { /* Backup domain reset.*/ RCC->BDCR = RCC_BDCR_BDRST; RCC->BDCR = 0; } #if STM32_LSE_ENABLED #if defined(STM32_LSE_BYPASS) /* LSE Bypass.*/ RCC->BDCR |= RCC_BDCR_LSEON | RCC_BDCR_LSEBYP; #else /* No LSE Bypass.*/ RCC->BDCR |= RCC_BDCR_LSEON; #endif while ((RCC->BDCR & RCC_BDCR_LSERDY) == 0) ; /* Waits until LSE is stable. */ #endif #if HAL_USE_RTC /* If the backup domain hasn't been initialized yet then proceed with initialization.*/ if ((RCC->BDCR & RCC_BDCR_RTCEN) == 0) { /* Selects clock source.*/ RCC->BDCR |= STM32_RTCSEL; /* RTC clock enabled.*/ RCC->BDCR |= RCC_BDCR_RTCEN; } #endif /* HAL_USE_RTC */ #if STM32_BKPRAM_ENABLE rccEnableBKPSRAM(false); PWR->CSR |= PWR_CSR_BRE; while ((PWR->CSR & PWR_CSR_BRR) == 0) ; /* Waits until the regulator is stable */ #else PWR->CSR &= ~PWR_CSR_BRE; #endif /* STM32_BKPRAM_ENABLE */ } /*===========================================================================*/ /* Driver interrupt handlers. */ /*===========================================================================*/ /*===========================================================================*/ /* Driver exported functions. */ /*===========================================================================*/ /** * @brief Low level HAL driver initialization. * * @notapi */ void hal_lld_init(void) { /* Reset of all peripherals. AHB3 is not reseted because it could have been initialized in the board initialization file (board.c).*/ rccResetAHB1(~0); rccResetAHB2(~0); rccResetAPB1(~RCC_APB1RSTR_PWRRST); rccResetAPB2(~0); /* SysTick initialization using the system clock.*/ SysTick->LOAD = STM32_HCLK / CH_FREQUENCY - 1; SysTick->VAL = 0; SysTick->CTRL = SysTick_CTRL_CLKSOURCE_Msk | SysTick_CTRL_ENABLE_Msk | SysTick_CTRL_TICKINT_Msk; /* DWT cycle counter enable.*/ SCS_DEMCR |= SCS_DEMCR_TRCENA; DWT_CTRL |= DWT_CTRL_CYCCNTENA; /* PWR clock enabled.*/ rccEnablePWRInterface(FALSE); /* Initializes the backup domain.*/ hal_lld_backup_domain_init(); #if defined(STM32_DMA_REQUIRED) dmaInit(); #endif /* Programmable voltage detector enable.*/ #if STM32_PVD_ENABLE PWR->CR |= PWR_CR_PVDE | (STM32_PLS & STM32_PLS_MASK); #endif /* STM32_PVD_ENABLE */ } /** * @brief STM32F2xx clocks and PLL initialization. * @note All the involved constants come from the file @p board.h. * @note This function should be invoked just after the system reset. * * @special */ void stm32_clock_init(void) { #if !STM32_NO_INIT /* PWR clock enable.*/ RCC->APB1ENR = RCC_APB1ENR_PWREN; /* PWR initialization.*/ #if defined(STM32F4XX) || defined(__DOXYGEN__) PWR->CR = STM32_VOS; #else PWR->CR = 0; #endif /* HSI setup, it enforces the reset situation in order to handle possible problems with JTAG probes and re-initializations.*/ RCC->CR |= RCC_CR_HSION; /* Make sure HSI is ON. */ while (!(RCC->CR & RCC_CR_HSIRDY)) ; /* Wait until HSI is stable. */ RCC->CR &= RCC_CR_HSITRIM | RCC_CR_HSION; /* CR Reset value. */ RCC->CFGR = 0; /* CFGR reset value. */ while ((RCC->CFGR & RCC_CFGR_SWS) != RCC_CFGR_SWS_HSI) ; /* Waits until HSI is selected. */ #if STM32_HSE_ENABLED /* HSE activation.*/ #if defined(STM32_HSE_BYPASS) /* HSE Bypass.*/ RCC->CR |= RCC_CR_HSEON | RCC_CR_HSEBYP; #else /* No HSE Bypass.*/ RCC->CR |= RCC_CR_HSEON; #endif while ((RCC->CR & RCC_CR_HSERDY) == 0) ; /* Waits until HSE is stable. */ #endif #if STM32_LSI_ENABLED /* LSI activation.*/ RCC->CSR |= RCC_CSR_LSION; while ((RCC->CSR & RCC_CSR_LSIRDY) == 0) ; /* Waits until LSI is stable. */ #endif #if STM32_ACTIVATE_PLL /* PLL activation.*/ RCC->PLLCFGR = STM32_PLLQ | STM32_PLLSRC | STM32_PLLP | STM32_PLLN | STM32_PLLM; RCC->CR |= RCC_CR_PLLON; /* Synchronization with voltage regulator stabilization.*/ #if defined(STM32F4XX) while ((PWR->CSR & PWR_CSR_VOSRDY) == 0) ; /* Waits until power regulator is stable. */ #if STM32_OVERDRIVE_REQUIRED /* Overdrive activation performed after activating the PLL in order to save time as recommended in RM in "Entering Over-drive mode" paragraph.*/ PWR->CR |= PWR_CR_ODEN; while (!(PWR->CSR & PWR_CSR_ODRDY)) ; PWR->CR |= PWR_CR_ODSWEN; while (!(PWR->CSR & PWR_CSR_ODSWRDY)) ; #endif /* STM32_OVERDRIVE_REQUIRED */ #endif /* defined(STM32F4XX) */ /* Waiting for PLL lock.*/ while (!(RCC->CR & RCC_CR_PLLRDY)) ; #endif /* STM32_OVERDRIVE_REQUIRED */ #if STM32_ACTIVATE_PLLI2S /* PLLI2S activation.*/ RCC->PLLI2SCFGR = STM32_PLLI2SR | STM32_PLLI2SN; RCC->CR |= RCC_CR_PLLI2SON; /* Waiting for PLL lock.*/ while (!(RCC->CR & RCC_CR_PLLI2SRDY)) ; #endif /* Other clock-related settings (dividers, MCO etc).*/ RCC->CFGR = STM32_MCO2PRE | STM32_MCO2SEL | STM32_MCO1PRE | STM32_MCO1SEL | STM32_RTCPRE | STM32_PPRE2 | STM32_PPRE1 | STM32_HPRE; /* Flash setup.*/ #if defined(STM32_USE_REVISION_A_FIX) /* Some old revisions of F4x MCUs randomly crashes with compiler optimizations enabled AND flash caches enabled. */ if ((DBGMCU->IDCODE == 0x20006411) && (SCB->CPUID == 0x410FC241)) FLASH->ACR = FLASH_ACR_PRFTEN | STM32_FLASHBITS; else FLASH->ACR = FLASH_ACR_PRFTEN | FLASH_ACR_ICEN | FLASH_ACR_DCEN | STM32_FLASHBITS; #else FLASH->ACR = FLASH_ACR_PRFTEN | FLASH_ACR_ICEN | FLASH_ACR_DCEN | STM32_FLASHBITS; #endif /* Switching to the configured clock source if it is different from MSI.*/ #if (STM32_SW != STM32_SW_HSI) RCC->CFGR |= STM32_SW; /* Switches on the selected clock source. */ while ((RCC->CFGR & RCC_CFGR_SWS) != (STM32_SW << 2)) ; #endif #endif /* STM32_NO_INIT */ /* SYSCFG clock enabled here because it is a multi-functional unit shared among multiple drivers.*/ rccEnableAPB2(RCC_APB2ENR_SYSCFGEN, TRUE); } /** @} */