diff --git a/boards/OLIMEX_STM32_P107/board.c b/boards/OLIMEX_STM32_P107/board.c
index 6734597fc..3d4aaafbe 100644
--- a/boards/OLIMEX_STM32_P107/board.c
+++ b/boards/OLIMEX_STM32_P107/board.c
@@ -47,6 +47,30 @@ void __early_init(void) {
stm32_clock_init();
}
+#if HAL_USE_MMC_SPI
+/*
+ * Card detection through the card internal pull-up on D3.
+ */
+bool_t mmc_lld_is_card_inserted(MMCDriver *mmcp) {
+ static bool_t last_status = FALSE;
+
+ (void)mmcp;
+ if ((palReadLatch(GPIOA) & PAL_PORT_BIT(GPIOA_SPI3_CS_MMC)) == 0)
+ return last_status;
+ return last_status = (bool_t)palReadPad(GPIOA, GPIOA_SPI3_CS_MMC);
+}
+
+/*
+ * Card write protection detection is not possible, the card is always
+ * reported as not protected.
+ */
+bool_t mmc_lld_is_write_protected(MMCDriver *mmcp) {
+
+ (void)mmcp;
+ return FALSE;
+}
+#endif
+
/*
* Board-specific initialization code.
*/
diff --git a/boards/OLIMEX_STM32_P107/board.h b/boards/OLIMEX_STM32_P107/board.h
index 36aa52fa2..5016159f8 100644
--- a/boards/OLIMEX_STM32_P107/board.h
+++ b/boards/OLIMEX_STM32_P107/board.h
@@ -22,14 +22,14 @@
#define _BOARD_H_
/*
- * Setup for the Olimex STM32-P107 evaluation board.
+ * Setup for the Olimex STM32-P107 Rev.A evaluation board.
*/
/*
* Board identifier.
*/
-#define BOARD_OLIMEX_STM32_P107
-#define BOARD_NAME "Olimex STM32-P107"
+#define BOARD_OLIMEX_STM32_P107_REV_A
+#define BOARD_NAME "Olimex STM32-P107 Rev.A"
/*
* Board frequencies.
@@ -52,7 +52,7 @@
* IO pins assignments.
*/
#define GPIOA_SWITCH_WKUP 0
-
+#define GPIOA_SPI3_CS_MMC 4
#define GPIOC_LED_STATUS1 6
#define GPIOC_LED_STATUS2 7
#define GPIOC_SWITCH_TAMPER 13
@@ -88,7 +88,7 @@
* PA1 - Normal input (ETH_RMII_REF_CLK).
* PA2 - Alternate output (ETH_RMII_MDIO).
* PA3 - Input with PU (unconnected).
- * PA4 - Push Pull output (CS_MMC).
+ * PA4 - Open Drain output (CS_MMC).
* PA5 - Input with PU (unconnected).
* PA6 - Input with PU (unconnected).
* PA7 - Normal input (ETH_RMII_CRS_DV).
@@ -101,7 +101,7 @@
* PA14 - Normal input (TCK).
* PA15 - Normal input (TDI).
*/
-#define VAL_GPIOACRL 0x48838B44 /* PA7...PA0 */
+#define VAL_GPIOACRL 0x48878B44 /* PA7...PA0 */
#define VAL_GPIOACRH 0x4444444B /* PA15...PA8 */
#define VAL_GPIOAODR 0xFFFFFFFF
diff --git a/demos/ARMCM3-STM32F107-FATFS/Makefile b/demos/ARMCM3-STM32F107-FATFS/Makefile
new file mode 100644
index 000000000..f5dc94fa1
--- /dev/null
+++ b/demos/ARMCM3-STM32F107-FATFS/Makefile
@@ -0,0 +1,212 @@
+##############################################################################
+# Build global options
+# NOTE: Can be overridden externally.
+#
+
+# Compiler options here.
+ifeq ($(USE_OPT),)
+ USE_OPT = -O2 -ggdb -fomit-frame-pointer -falign-functions=16
+endif
+
+# C specific options here (added to USE_OPT).
+ifeq ($(USE_COPT),)
+ USE_COPT =
+endif
+
+# C++ specific options here (added to USE_OPT).
+ifeq ($(USE_CPPOPT),)
+ USE_CPPOPT = -fno-rtti
+endif
+
+# Enable this if you want the linker to remove unused code and data
+ifeq ($(USE_LINK_GC),)
+ USE_LINK_GC = yes
+endif
+
+# If enabled, this option allows to compile the application in THUMB mode.
+ifeq ($(USE_THUMB),)
+ USE_THUMB = yes
+endif
+
+# Enable this if you want to see the full log while compiling.
+ifeq ($(USE_VERBOSE_COMPILE),)
+ USE_VERBOSE_COMPILE = no
+endif
+
+#
+# Build global options
+##############################################################################
+
+##############################################################################
+# Architecture or project specific options
+#
+
+# Enable this if you really want to use the STM FWLib.
+ifeq ($(USE_FWLIB),)
+ USE_FWLIB = no
+endif
+
+#
+# Architecture or project specific options
+##############################################################################
+
+##############################################################################
+# Project, sources and paths
+#
+
+# Define project name here
+PROJECT = ch
+
+# Imported source files and paths
+CHIBIOS = ../..
+include $(CHIBIOS)/boards/OLIMEX_STM32_P107/board.mk
+include $(CHIBIOS)/os/hal/platforms/STM32F1xx/platform.mk
+include $(CHIBIOS)/os/hal/hal.mk
+include $(CHIBIOS)/os/ports/GCC/ARMCMx/STM32F1xx/port.mk
+include $(CHIBIOS)/os/kernel/kernel.mk
+include $(CHIBIOS)/os/various/fatfs_bindings/fatfs.mk
+include $(CHIBIOS)/test/test.mk
+
+# Define linker script file here
+LDSCRIPT= $(PORTLD)/STM32F107xC.ld
+
+# C sources that can be compiled in ARM or THUMB mode depending on the global
+# setting.
+CSRC = $(PORTSRC) \
+ $(KERNSRC) \
+ $(HALSRC) \
+ $(PLATFORMSRC) \
+ $(BOARDSRC) \
+ $(FATFSSRC) \
+ $(TESTSRC) \
+ $(CHIBIOS)/os/various/shell.c \
+ $(CHIBIOS)/os/various/chprintf.c \
+ main.c
+
+# C++ sources that can be compiled in ARM or THUMB mode depending on the global
+# setting.
+CPPSRC =
+
+# C sources to be compiled in ARM mode regardless of the global setting.
+# NOTE: Mixing ARM and THUMB mode enables the -mthumb-interwork compiler
+# option that results in lower performance and larger code size.
+ACSRC =
+
+# C++ sources to be compiled in ARM mode regardless of the global setting.
+# NOTE: Mixing ARM and THUMB mode enables the -mthumb-interwork compiler
+# option that results in lower performance and larger code size.
+ACPPSRC =
+
+# C sources to be compiled in THUMB mode regardless of the global setting.
+# NOTE: Mixing ARM and THUMB mode enables the -mthumb-interwork compiler
+# option that results in lower performance and larger code size.
+TCSRC =
+
+# C sources to be compiled in THUMB mode regardless of the global setting.
+# NOTE: Mixing ARM and THUMB mode enables the -mthumb-interwork compiler
+# option that results in lower performance and larger code size.
+TCPPSRC =
+
+# List ASM source files here
+ASMSRC = $(PORTASM)
+
+INCDIR = $(PORTINC) $(KERNINC) $(TESTINC) \
+ $(HALINC) $(PLATFORMINC) $(BOARDINC) \
+ $(FATFSINC) \
+ $(CHIBIOS)/os/various
+
+#
+# Project, sources and paths
+##############################################################################
+
+##############################################################################
+# Compiler settings
+#
+
+MCU = cortex-m3
+
+#TRGT = arm-elf-
+TRGT = arm-none-eabi-
+CC = $(TRGT)gcc
+CPPC = $(TRGT)g++
+# Enable loading with g++ only if you need C++ runtime support.
+# NOTE: You can use C++ even without C++ support if you are careful. C++
+# runtime support makes code size explode.
+LD = $(TRGT)gcc
+#LD = $(TRGT)g++
+CP = $(TRGT)objcopy
+AS = $(TRGT)gcc -x assembler-with-cpp
+OD = $(TRGT)objdump
+HEX = $(CP) -O ihex
+BIN = $(CP) -O binary
+
+# ARM-specific options here
+AOPT =
+
+# THUMB-specific options here
+TOPT = -mthumb -DTHUMB
+
+# Define C warning options here
+CWARN = -Wall -Wextra -Wstrict-prototypes
+
+# Define C++ warning options here
+CPPWARN = -Wall -Wextra
+
+#
+# Compiler settings
+##############################################################################
+
+##############################################################################
+# Start of default section
+#
+
+# List all default C defines here, like -D_DEBUG=1
+DDEFS =
+
+# List all default ASM defines here, like -D_DEBUG=1
+DADEFS =
+
+# List all default directories to look for include files here
+DINCDIR =
+
+# List the default directory to look for the libraries here
+DLIBDIR =
+
+# List all default libraries here
+DLIBS =
+
+#
+# End of default section
+##############################################################################
+
+##############################################################################
+# Start of user section
+#
+
+# List all user C define here, like -D_DEBUG=1
+UDEFS =
+
+# Define ASM defines here
+UADEFS =
+
+# List all user directories here
+UINCDIR =
+
+# List the user directory to look for the libraries here
+ULIBDIR =
+
+# List all user libraries here
+ULIBS =
+
+#
+# End of user defines
+##############################################################################
+
+ifeq ($(USE_FWLIB),yes)
+ include $(CHIBIOS)/ext/stm32lib/stm32lib.mk
+ CSRC += $(STM32SRC)
+ INCDIR += $(STM32INC)
+ USE_OPT += -DUSE_STDPERIPH_DRIVER
+endif
+
+include $(CHIBIOS)/os/ports/GCC/ARMCMx/rules.mk
diff --git a/demos/ARMCM3-STM32F107-FATFS/chconf.h b/demos/ARMCM3-STM32F107-FATFS/chconf.h
new file mode 100644
index 000000000..b1f2cd62c
--- /dev/null
+++ b/demos/ARMCM3-STM32F107-FATFS/chconf.h
@@ -0,0 +1,535 @@
+/*
+ ChibiOS/RT - Copyright (C) 2006,2007,2008,2009,2010,
+ 2011,2012 Giovanni Di Sirio.
+
+ This file is part of ChibiOS/RT.
+
+ ChibiOS/RT is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 3 of the License, or
+ (at your option) any later version.
+
+ ChibiOS/RT is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program. If not, see .
+*/
+
+/**
+ * @file templates/chconf.h
+ * @brief Configuration file template.
+ * @details A copy of this file must be placed in each project directory, it
+ * contains the application specific kernel settings.
+ *
+ * @addtogroup config
+ * @details Kernel related settings and hooks.
+ * @{
+ */
+
+#ifndef _CHCONF_H_
+#define _CHCONF_H_
+
+/*===========================================================================*/
+/**
+ * @name Kernel parameters and options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief System tick frequency.
+ * @details Frequency of the system timer that drives the system ticks. This
+ * setting also defines the system tick time unit.
+ */
+#if !defined(CH_FREQUENCY) || defined(__DOXYGEN__)
+#define CH_FREQUENCY 1000
+#endif
+
+/**
+ * @brief Round robin interval.
+ * @details This constant is the number of system ticks allowed for the
+ * threads before preemption occurs. Setting this value to zero
+ * disables the preemption for threads with equal priority and the
+ * round robin becomes cooperative. Note that higher priority
+ * threads can still preempt, the kernel is always preemptive.
+ *
+ * @note Disabling the round robin preemption makes the kernel more compact
+ * and generally faster.
+ */
+#if !defined(CH_TIME_QUANTUM) || defined(__DOXYGEN__)
+#define CH_TIME_QUANTUM 20
+#endif
+
+/**
+ * @brief Managed RAM size.
+ * @details Size of the RAM area to be managed by the OS. If set to zero
+ * then the whole available RAM is used. The core memory is made
+ * available to the heap allocator and/or can be used directly through
+ * the simplified core memory allocator.
+ *
+ * @note In order to let the OS manage the whole RAM the linker script must
+ * provide the @p __heap_base__ and @p __heap_end__ symbols.
+ * @note Requires @p CH_USE_MEMCORE.
+ */
+#if !defined(CH_MEMCORE_SIZE) || defined(__DOXYGEN__)
+#define CH_MEMCORE_SIZE 0
+#endif
+
+/**
+ * @brief Idle thread automatic spawn suppression.
+ * @details When this option is activated the function @p chSysInit()
+ * does not spawn the idle thread automatically. The application has
+ * then the responsibility to do one of the following:
+ * - Spawn a custom idle thread at priority @p IDLEPRIO.
+ * - Change the main() thread priority to @p IDLEPRIO then enter
+ * an endless loop. In this scenario the @p main() thread acts as
+ * the idle thread.
+ * .
+ * @note Unless an idle thread is spawned the @p main() thread must not
+ * enter a sleep state.
+ */
+#if !defined(CH_NO_IDLE_THREAD) || defined(__DOXYGEN__)
+#define CH_NO_IDLE_THREAD FALSE
+#endif
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Performance options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief OS optimization.
+ * @details If enabled then time efficient rather than space efficient code
+ * is used when two possible implementations exist.
+ *
+ * @note This is not related to the compiler optimization options.
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_OPTIMIZE_SPEED) || defined(__DOXYGEN__)
+#define CH_OPTIMIZE_SPEED TRUE
+#endif
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Subsystem options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Threads registry APIs.
+ * @details If enabled then the registry APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_USE_REGISTRY) || defined(__DOXYGEN__)
+#define CH_USE_REGISTRY TRUE
+#endif
+
+/**
+ * @brief Threads synchronization APIs.
+ * @details If enabled then the @p chThdWait() function is included in
+ * the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_USE_WAITEXIT) || defined(__DOXYGEN__)
+#define CH_USE_WAITEXIT TRUE
+#endif
+
+/**
+ * @brief Semaphores APIs.
+ * @details If enabled then the Semaphores APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_USE_SEMAPHORES) || defined(__DOXYGEN__)
+#define CH_USE_SEMAPHORES TRUE
+#endif
+
+/**
+ * @brief Semaphores queuing mode.
+ * @details If enabled then the threads are enqueued on semaphores by
+ * priority rather than in FIFO order.
+ *
+ * @note The default is @p FALSE. Enable this if you have special requirements.
+ * @note Requires @p CH_USE_SEMAPHORES.
+ */
+#if !defined(CH_USE_SEMAPHORES_PRIORITY) || defined(__DOXYGEN__)
+#define CH_USE_SEMAPHORES_PRIORITY FALSE
+#endif
+
+/**
+ * @brief Atomic semaphore API.
+ * @details If enabled then the semaphores the @p chSemSignalWait() API
+ * is included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_USE_SEMAPHORES.
+ */
+#if !defined(CH_USE_SEMSW) || defined(__DOXYGEN__)
+#define CH_USE_SEMSW TRUE
+#endif
+
+/**
+ * @brief Mutexes APIs.
+ * @details If enabled then the mutexes APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_USE_MUTEXES) || defined(__DOXYGEN__)
+#define CH_USE_MUTEXES TRUE
+#endif
+
+/**
+ * @brief Conditional Variables APIs.
+ * @details If enabled then the conditional variables APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_USE_MUTEXES.
+ */
+#if !defined(CH_USE_CONDVARS) || defined(__DOXYGEN__)
+#define CH_USE_CONDVARS TRUE
+#endif
+
+/**
+ * @brief Conditional Variables APIs with timeout.
+ * @details If enabled then the conditional variables APIs with timeout
+ * specification are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_USE_CONDVARS.
+ */
+#if !defined(CH_USE_CONDVARS_TIMEOUT) || defined(__DOXYGEN__)
+#define CH_USE_CONDVARS_TIMEOUT TRUE
+#endif
+
+/**
+ * @brief Events Flags APIs.
+ * @details If enabled then the event flags APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_USE_EVENTS) || defined(__DOXYGEN__)
+#define CH_USE_EVENTS TRUE
+#endif
+
+/**
+ * @brief Events Flags APIs with timeout.
+ * @details If enabled then the events APIs with timeout specification
+ * are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_USE_EVENTS.
+ */
+#if !defined(CH_USE_EVENTS_TIMEOUT) || defined(__DOXYGEN__)
+#define CH_USE_EVENTS_TIMEOUT TRUE
+#endif
+
+/**
+ * @brief Synchronous Messages APIs.
+ * @details If enabled then the synchronous messages APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_USE_MESSAGES) || defined(__DOXYGEN__)
+#define CH_USE_MESSAGES TRUE
+#endif
+
+/**
+ * @brief Synchronous Messages queuing mode.
+ * @details If enabled then messages are served by priority rather than in
+ * FIFO order.
+ *
+ * @note The default is @p FALSE. Enable this if you have special requirements.
+ * @note Requires @p CH_USE_MESSAGES.
+ */
+#if !defined(CH_USE_MESSAGES_PRIORITY) || defined(__DOXYGEN__)
+#define CH_USE_MESSAGES_PRIORITY FALSE
+#endif
+
+/**
+ * @brief Mailboxes APIs.
+ * @details If enabled then the asynchronous messages (mailboxes) APIs are
+ * included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_USE_SEMAPHORES.
+ */
+#if !defined(CH_USE_MAILBOXES) || defined(__DOXYGEN__)
+#define CH_USE_MAILBOXES TRUE
+#endif
+
+/**
+ * @brief I/O Queues APIs.
+ * @details If enabled then the I/O queues APIs are included in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_USE_QUEUES) || defined(__DOXYGEN__)
+#define CH_USE_QUEUES TRUE
+#endif
+
+/**
+ * @brief Core Memory Manager APIs.
+ * @details If enabled then the core memory manager APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_USE_MEMCORE) || defined(__DOXYGEN__)
+#define CH_USE_MEMCORE TRUE
+#endif
+
+/**
+ * @brief Heap Allocator APIs.
+ * @details If enabled then the memory heap allocator APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_USE_MEMCORE and either @p CH_USE_MUTEXES or
+ * @p CH_USE_SEMAPHORES.
+ * @note Mutexes are recommended.
+ */
+#if !defined(CH_USE_HEAP) || defined(__DOXYGEN__)
+#define CH_USE_HEAP TRUE
+#endif
+
+/**
+ * @brief C-runtime allocator.
+ * @details If enabled the the heap allocator APIs just wrap the C-runtime
+ * @p malloc() and @p free() functions.
+ *
+ * @note The default is @p FALSE.
+ * @note Requires @p CH_USE_HEAP.
+ * @note The C-runtime may or may not require @p CH_USE_MEMCORE, see the
+ * appropriate documentation.
+ */
+#if !defined(CH_USE_MALLOC_HEAP) || defined(__DOXYGEN__)
+#define CH_USE_MALLOC_HEAP FALSE
+#endif
+
+/**
+ * @brief Memory Pools Allocator APIs.
+ * @details If enabled then the memory pools allocator APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ */
+#if !defined(CH_USE_MEMPOOLS) || defined(__DOXYGEN__)
+#define CH_USE_MEMPOOLS TRUE
+#endif
+
+/**
+ * @brief Dynamic Threads APIs.
+ * @details If enabled then the dynamic threads creation APIs are included
+ * in the kernel.
+ *
+ * @note The default is @p TRUE.
+ * @note Requires @p CH_USE_WAITEXIT.
+ * @note Requires @p CH_USE_HEAP and/or @p CH_USE_MEMPOOLS.
+ */
+#if !defined(CH_USE_DYNAMIC) || defined(__DOXYGEN__)
+#define CH_USE_DYNAMIC TRUE
+#endif
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Debug options
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Debug option, system state check.
+ * @details If enabled the correct call protocol for system APIs is checked
+ * at runtime.
+ *
+ * @note The default is @p FALSE.
+ */
+#if !defined(CH_DBG_SYSTEM_STATE_CHECK) || defined(__DOXYGEN__)
+#define CH_DBG_SYSTEM_STATE_CHECK FALSE
+#endif
+
+/**
+ * @brief Debug option, parameters checks.
+ * @details If enabled then the checks on the API functions input
+ * parameters are activated.
+ *
+ * @note The default is @p FALSE.
+ */
+#if !defined(CH_DBG_ENABLE_CHECKS) || defined(__DOXYGEN__)
+#define CH_DBG_ENABLE_CHECKS FALSE
+#endif
+
+/**
+ * @brief Debug option, consistency checks.
+ * @details If enabled then all the assertions in the kernel code are
+ * activated. This includes consistency checks inside the kernel,
+ * runtime anomalies and port-defined checks.
+ *
+ * @note The default is @p FALSE.
+ */
+#if !defined(CH_DBG_ENABLE_ASSERTS) || defined(__DOXYGEN__)
+#define CH_DBG_ENABLE_ASSERTS FALSE
+#endif
+
+/**
+ * @brief Debug option, trace buffer.
+ * @details If enabled then the context switch circular trace buffer is
+ * activated.
+ *
+ * @note The default is @p FALSE.
+ */
+#if !defined(CH_DBG_ENABLE_TRACE) || defined(__DOXYGEN__)
+#define CH_DBG_ENABLE_TRACE FALSE
+#endif
+
+/**
+ * @brief Debug option, stack checks.
+ * @details If enabled then a runtime stack check is performed.
+ *
+ * @note The default is @p FALSE.
+ * @note The stack check is performed in a architecture/port dependent way.
+ * It may not be implemented or some ports.
+ * @note The default failure mode is to halt the system with the global
+ * @p panic_msg variable set to @p NULL.
+ */
+#if !defined(CH_DBG_ENABLE_STACK_CHECK) || defined(__DOXYGEN__)
+#define CH_DBG_ENABLE_STACK_CHECK FALSE
+#endif
+
+/**
+ * @brief Debug option, stacks initialization.
+ * @details If enabled then the threads working area is filled with a byte
+ * value when a thread is created. This can be useful for the
+ * runtime measurement of the used stack.
+ *
+ * @note The default is @p FALSE.
+ */
+#if !defined(CH_DBG_FILL_THREADS) || defined(__DOXYGEN__)
+#define CH_DBG_FILL_THREADS FALSE
+#endif
+
+/**
+ * @brief Debug option, threads profiling.
+ * @details If enabled then a field is added to the @p Thread structure that
+ * counts the system ticks occurred while executing the thread.
+ *
+ * @note The default is @p TRUE.
+ * @note This debug option is defaulted to TRUE because it is required by
+ * some test cases into the test suite.
+ */
+#if !defined(CH_DBG_THREADS_PROFILING) || defined(__DOXYGEN__)
+#define CH_DBG_THREADS_PROFILING TRUE
+#endif
+
+/** @} */
+
+/*===========================================================================*/
+/**
+ * @name Kernel hooks
+ * @{
+ */
+/*===========================================================================*/
+
+/**
+ * @brief Threads descriptor structure extension.
+ * @details User fields added to the end of the @p Thread structure.
+ */
+#if !defined(THREAD_EXT_FIELDS) || defined(__DOXYGEN__)
+#define THREAD_EXT_FIELDS \
+ /* Add threads custom fields here.*/
+#endif
+
+/**
+ * @brief Threads initialization hook.
+ * @details User initialization code added to the @p chThdInit() API.
+ *
+ * @note It is invoked from within @p chThdInit() and implicitly from all
+ * the threads creation APIs.
+ */
+#if !defined(THREAD_EXT_INIT_HOOK) || defined(__DOXYGEN__)
+#define THREAD_EXT_INIT_HOOK(tp) { \
+ /* Add threads initialization code here.*/ \
+}
+#endif
+
+/**
+ * @brief Threads finalization hook.
+ * @details User finalization code added to the @p chThdExit() API.
+ *
+ * @note It is inserted into lock zone.
+ * @note It is also invoked when the threads simply return in order to
+ * terminate.
+ */
+#if !defined(THREAD_EXT_EXIT_HOOK) || defined(__DOXYGEN__)
+#define THREAD_EXT_EXIT_HOOK(tp) { \
+ /* Add threads finalization code here.*/ \
+}
+#endif
+
+/**
+ * @brief Context switch hook.
+ * @details This hook is invoked just before switching between threads.
+ */
+#if !defined(THREAD_CONTEXT_SWITCH_HOOK) || defined(__DOXYGEN__)
+#define THREAD_CONTEXT_SWITCH_HOOK(ntp, otp) { \
+ /* System halt code here.*/ \
+}
+#endif
+
+/**
+ * @brief Idle Loop hook.
+ * @details This hook is continuously invoked by the idle thread loop.
+ */
+#if !defined(IDLE_LOOP_HOOK) || defined(__DOXYGEN__)
+#define IDLE_LOOP_HOOK() { \
+ /* Idle loop code here.*/ \
+}
+#endif
+
+/**
+ * @brief System tick event hook.
+ * @details This hook is invoked in the system tick handler immediately
+ * after processing the virtual timers queue.
+ */
+#if !defined(SYSTEM_TICK_EVENT_HOOK) || defined(__DOXYGEN__)
+#define SYSTEM_TICK_EVENT_HOOK() { \
+ /* System tick event code here.*/ \
+}
+#endif
+
+/**
+ * @brief System halt hook.
+ * @details This hook is invoked in case to a system halting error before
+ * the system is halted.
+ */
+#if !defined(SYSTEM_HALT_HOOK) || defined(__DOXYGEN__)
+#define SYSTEM_HALT_HOOK() { \
+ /* System halt code here.*/ \
+}
+#endif
+
+/** @} */
+
+/*===========================================================================*/
+/* Port-specific settings (override port settings defaulted in chcore.h). */
+/*===========================================================================*/
+
+#endif /* _CHCONF_H_ */
+
+/** @} */
diff --git a/demos/ARMCM3-STM32F107-FATFS/ffconf.h b/demos/ARMCM3-STM32F107-FATFS/ffconf.h
new file mode 100644
index 000000000..e6a13cea3
--- /dev/null
+++ b/demos/ARMCM3-STM32F107-FATFS/ffconf.h
@@ -0,0 +1,193 @@
+/* CHIBIOS FIX */
+#include "ch.h"
+
+/*---------------------------------------------------------------------------/
+/ FatFs - FAT file system module configuration file R0.09 (C)ChaN, 2011
+/----------------------------------------------------------------------------/
+/
+/ CAUTION! Do not forget to make clean the project after any changes to
+/ the configuration options.
+/
+/----------------------------------------------------------------------------*/
+#ifndef _FFCONF
+#define _FFCONF 6502 /* Revision ID */
+
+
+/*---------------------------------------------------------------------------/
+/ Functions and Buffer Configurations
+/----------------------------------------------------------------------------*/
+
+#define _FS_TINY 0 /* 0:Normal or 1:Tiny */
+/* When _FS_TINY is set to 1, FatFs uses the sector buffer in the file system
+/ object instead of the sector buffer in the individual file object for file
+/ data transfer. This reduces memory consumption 512 bytes each file object. */
+
+
+#define _FS_READONLY 0 /* 0:Read/Write or 1:Read only */
+/* Setting _FS_READONLY to 1 defines read only configuration. This removes
+/ writing functions, f_write, f_sync, f_unlink, f_mkdir, f_chmod, f_rename,
+/ f_truncate and useless f_getfree. */
+
+
+#define _FS_MINIMIZE 0 /* 0 to 3 */
+/* The _FS_MINIMIZE option defines minimization level to remove some functions.
+/
+/ 0: Full function.
+/ 1: f_stat, f_getfree, f_unlink, f_mkdir, f_chmod, f_truncate and f_rename
+/ are removed.
+/ 2: f_opendir and f_readdir are removed in addition to 1.
+/ 3: f_lseek is removed in addition to 2. */
+
+
+#define _USE_STRFUNC 0 /* 0:Disable or 1-2:Enable */
+/* To enable string functions, set _USE_STRFUNC to 1 or 2. */
+
+
+#define _USE_MKFS 0 /* 0:Disable or 1:Enable */
+/* To enable f_mkfs function, set _USE_MKFS to 1 and set _FS_READONLY to 0 */
+
+
+#define _USE_FORWARD 0 /* 0:Disable or 1:Enable */
+/* To enable f_forward function, set _USE_FORWARD to 1 and set _FS_TINY to 1. */
+
+
+#define _USE_FASTSEEK 0 /* 0:Disable or 1:Enable */
+/* To enable fast seek feature, set _USE_FASTSEEK to 1. */
+
+
+
+/*---------------------------------------------------------------------------/
+/ Locale and Namespace Configurations
+/----------------------------------------------------------------------------*/
+
+#define _CODE_PAGE 1252
+/* The _CODE_PAGE specifies the OEM code page to be used on the target system.
+/ Incorrect setting of the code page can cause a file open failure.
+/
+/ 932 - Japanese Shift-JIS (DBCS, OEM, Windows)
+/ 936 - Simplified Chinese GBK (DBCS, OEM, Windows)
+/ 949 - Korean (DBCS, OEM, Windows)
+/ 950 - Traditional Chinese Big5 (DBCS, OEM, Windows)
+/ 1250 - Central Europe (Windows)
+/ 1251 - Cyrillic (Windows)
+/ 1252 - Latin 1 (Windows)
+/ 1253 - Greek (Windows)
+/ 1254 - Turkish (Windows)
+/ 1255 - Hebrew (Windows)
+/ 1256 - Arabic (Windows)
+/ 1257 - Baltic (Windows)
+/ 1258 - Vietnam (OEM, Windows)
+/ 437 - U.S. (OEM)
+/ 720 - Arabic (OEM)
+/ 737 - Greek (OEM)
+/ 775 - Baltic (OEM)
+/ 850 - Multilingual Latin 1 (OEM)
+/ 858 - Multilingual Latin 1 + Euro (OEM)
+/ 852 - Latin 2 (OEM)
+/ 855 - Cyrillic (OEM)
+/ 866 - Russian (OEM)
+/ 857 - Turkish (OEM)
+/ 862 - Hebrew (OEM)
+/ 874 - Thai (OEM, Windows)
+/ 1 - ASCII only (Valid for non LFN cfg.)
+*/
+
+
+#define _USE_LFN 3 /* 0 to 3 */
+#define _MAX_LFN 255 /* Maximum LFN length to handle (12 to 255) */
+/* The _USE_LFN option switches the LFN support.
+/
+/ 0: Disable LFN feature. _MAX_LFN and _LFN_UNICODE have no effect.
+/ 1: Enable LFN with static working buffer on the BSS. Always NOT reentrant.
+/ 2: Enable LFN with dynamic working buffer on the STACK.
+/ 3: Enable LFN with dynamic working buffer on the HEAP.
+/
+/ The LFN working buffer occupies (_MAX_LFN + 1) * 2 bytes. To enable LFN,
+/ Unicode handling functions ff_convert() and ff_wtoupper() must be added
+/ to the project. When enable to use heap, memory control functions
+/ ff_memalloc() and ff_memfree() must be added to the project. */
+
+
+#define _LFN_UNICODE 0 /* 0:ANSI/OEM or 1:Unicode */
+/* To switch the character code set on FatFs API to Unicode,
+/ enable LFN feature and set _LFN_UNICODE to 1. */
+
+
+#define _FS_RPATH 0 /* 0 to 2 */
+/* The _FS_RPATH option configures relative path feature.
+/
+/ 0: Disable relative path feature and remove related functions.
+/ 1: Enable relative path. f_chdrive() and f_chdir() are available.
+/ 2: f_getcwd() is available in addition to 1.
+/
+/ Note that output of the f_readdir fnction is affected by this option. */
+
+
+
+/*---------------------------------------------------------------------------/
+/ Physical Drive Configurations
+/----------------------------------------------------------------------------*/
+
+#define _VOLUMES 1
+/* Number of volumes (logical drives) to be used. */
+
+
+#define _MAX_SS 512 /* 512, 1024, 2048 or 4096 */
+/* Maximum sector size to be handled.
+/ Always set 512 for memory card and hard disk but a larger value may be
+/ required for on-board flash memory, floppy disk and optical disk.
+/ When _MAX_SS is larger than 512, it configures FatFs to variable sector size
+/ and GET_SECTOR_SIZE command must be implememted to the disk_ioctl function. */
+
+
+#define _MULTI_PARTITION 0 /* 0:Single partition, 1/2:Enable multiple partition */
+/* When set to 0, each volume is bound to the same physical drive number and
+/ it can mount only first primaly partition. When it is set to 1, each volume
+/ is tied to the partitions listed in VolToPart[]. */
+
+
+#define _USE_ERASE 0 /* 0:Disable or 1:Enable */
+/* To enable sector erase feature, set _USE_ERASE to 1. CTRL_ERASE_SECTOR command
+/ should be added to the disk_ioctl functio. */
+
+
+
+/*---------------------------------------------------------------------------/
+/ System Configurations
+/----------------------------------------------------------------------------*/
+
+#define _WORD_ACCESS 0 /* 0 or 1 */
+/* Set 0 first and it is always compatible with all platforms. The _WORD_ACCESS
+/ option defines which access method is used to the word data on the FAT volume.
+/
+/ 0: Byte-by-byte access.
+/ 1: Word access. Do not choose this unless following condition is met.
+/
+/ When the byte order on the memory is big-endian or address miss-aligned word
+/ access results incorrect behavior, the _WORD_ACCESS must be set to 0.
+/ If it is not the case, the value can also be set to 1 to improve the
+/ performance and code size.
+*/
+
+
+/* A header file that defines sync object types on the O/S, such as
+/ windows.h, ucos_ii.h and semphr.h, must be included prior to ff.h. */
+
+#define _FS_REENTRANT 1 /* 0:Disable or 1:Enable */
+#define _FS_TIMEOUT 1000 /* Timeout period in unit of time ticks */
+#define _SYNC_t Semaphore * /* O/S dependent type of sync object. e.g. HANDLE, OS_EVENT*, ID and etc.. */
+
+/* The _FS_REENTRANT option switches the reentrancy (thread safe) of the FatFs module.
+/
+/ 0: Disable reentrancy. _SYNC_t and _FS_TIMEOUT have no effect.
+/ 1: Enable reentrancy. Also user provided synchronization handlers,
+/ ff_req_grant, ff_rel_grant, ff_del_syncobj and ff_cre_syncobj
+/ function must be added to the project. */
+
+
+#define _FS_SHARE 0 /* 0:Disable or >=1:Enable */
+/* To enable file shareing feature, set _FS_SHARE to 1 or greater. The value
+ defines how many files can be opened simultaneously. */
+
+
+#endif /* _FFCONFIG */
diff --git a/demos/ARMCM3-STM32F107-FATFS/halconf.h b/demos/ARMCM3-STM32F107-FATFS/halconf.h
new file mode 100644
index 000000000..40d5d756c
--- /dev/null
+++ b/demos/ARMCM3-STM32F107-FATFS/halconf.h
@@ -0,0 +1,342 @@
+/*
+ ChibiOS/RT - Copyright (C) 2006,2007,2008,2009,2010,
+ 2011,2012 Giovanni Di Sirio.
+
+ This file is part of ChibiOS/RT.
+
+ ChibiOS/RT is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 3 of the License, or
+ (at your option) any later version.
+
+ ChibiOS/RT is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program. If not, see .
+*/
+
+/**
+ * @file templates/halconf.h
+ * @brief HAL configuration header.
+ * @details HAL configuration file, this file allows to enable or disable the
+ * various device drivers from your application. You may also use
+ * this file in order to override the device drivers default settings.
+ *
+ * @addtogroup HAL_CONF
+ * @{
+ */
+
+#ifndef _HALCONF_H_
+#define _HALCONF_H_
+
+#include "mcuconf.h"
+
+/**
+ * @brief Enables the TM subsystem.
+ */
+#if !defined(HAL_USE_TM) || defined(__DOXYGEN__)
+#define HAL_USE_TM TRUE
+#endif
+
+/**
+ * @brief Enables the PAL subsystem.
+ */
+#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__)
+#define HAL_USE_PAL TRUE
+#endif
+
+/**
+ * @brief Enables the ADC subsystem.
+ */
+#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__)
+#define HAL_USE_ADC FALSE
+#endif
+
+/**
+ * @brief Enables the CAN subsystem.
+ */
+#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__)
+#define HAL_USE_CAN FALSE
+#endif
+
+/**
+ * @brief Enables the EXT subsystem.
+ */
+#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__)
+#define HAL_USE_EXT FALSE
+#endif
+
+/**
+ * @brief Enables the GPT subsystem.
+ */
+#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__)
+#define HAL_USE_GPT FALSE
+#endif
+
+/**
+ * @brief Enables the I2C subsystem.
+ */
+#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__)
+#define HAL_USE_I2C FALSE
+#endif
+
+/**
+ * @brief Enables the ICU subsystem.
+ */
+#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__)
+#define HAL_USE_ICU FALSE
+#endif
+
+/**
+ * @brief Enables the MAC subsystem.
+ */
+#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__)
+#define HAL_USE_MAC FALSE
+#endif
+
+/**
+ * @brief Enables the MMC_SPI subsystem.
+ */
+#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__)
+#define HAL_USE_MMC_SPI TRUE
+#endif
+
+/**
+ * @brief Enables the PWM subsystem.
+ */
+#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__)
+#define HAL_USE_PWM FALSE
+#endif
+
+/**
+ * @brief Enables the RTC subsystem.
+ */
+#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__)
+#define HAL_USE_RTC FALSE
+#endif
+
+/**
+ * @brief Enables the SDC subsystem.
+ */
+#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__)
+#define HAL_USE_SDC FALSE
+#endif
+
+/**
+ * @brief Enables the SERIAL subsystem.
+ */
+#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__)
+#define HAL_USE_SERIAL TRUE
+#endif
+
+/**
+ * @brief Enables the SERIAL over USB subsystem.
+ */
+#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__)
+#define HAL_USE_SERIAL_USB FALSE
+#endif
+
+/**
+ * @brief Enables the SPI subsystem.
+ */
+#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__)
+#define HAL_USE_SPI TRUE
+#endif
+
+/**
+ * @brief Enables the UART subsystem.
+ */
+#if !defined(HAL_USE_UART) || defined(__DOXYGEN__)
+#define HAL_USE_UART FALSE
+#endif
+
+/**
+ * @brief Enables the USB subsystem.
+ */
+#if !defined(HAL_USE_USB) || defined(__DOXYGEN__)
+#define HAL_USE_USB FALSE
+#endif
+
+/*===========================================================================*/
+/* ADC driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__)
+#define ADC_USE_WAIT TRUE
+#endif
+
+/**
+ * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define ADC_USE_MUTUAL_EXCLUSION TRUE
+#endif
+
+/*===========================================================================*/
+/* CAN driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Sleep mode related APIs inclusion switch.
+ */
+#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__)
+#define CAN_USE_SLEEP_MODE TRUE
+#endif
+
+/*===========================================================================*/
+/* I2C driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables the mutual exclusion APIs on the I2C bus.
+ */
+#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define I2C_USE_MUTUAL_EXCLUSION TRUE
+#endif
+
+/*===========================================================================*/
+/* MAC driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables an event sources for incoming packets.
+ */
+#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__)
+#define MAC_USE_EVENTS TRUE
+#endif
+
+/*===========================================================================*/
+/* MMC_SPI driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Block size for MMC transfers.
+ */
+#if !defined(MMC_SECTOR_SIZE) || defined(__DOXYGEN__)
+#define MMC_SECTOR_SIZE 512
+#endif
+
+/**
+ * @brief Delays insertions.
+ * @details If enabled this options inserts delays into the MMC waiting
+ * routines releasing some extra CPU time for the threads with
+ * lower priority, this may slow down the driver a bit however.
+ * This option is recommended also if the SPI driver does not
+ * use a DMA channel and heavily loads the CPU.
+ */
+#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__)
+#define MMC_NICE_WAITING TRUE
+#endif
+
+/**
+ * @brief Number of positive insertion queries before generating the
+ * insertion event.
+ */
+#if !defined(MMC_POLLING_INTERVAL) || defined(__DOXYGEN__)
+#define MMC_POLLING_INTERVAL 10
+#endif
+
+/**
+ * @brief Interval, in milliseconds, between insertion queries.
+ */
+#if !defined(MMC_POLLING_DELAY) || defined(__DOXYGEN__)
+#define MMC_POLLING_DELAY 10
+#endif
+
+/**
+ * @brief Uses the SPI polled API for small data transfers.
+ * @details Polled transfers usually improve performance because it
+ * saves two context switches and interrupt servicing. Note
+ * that this option has no effect on large transfers which
+ * are always performed using DMAs/IRQs.
+ */
+#if !defined(MMC_USE_SPI_POLLING) || defined(__DOXYGEN__)
+#define MMC_USE_SPI_POLLING TRUE
+#endif
+
+/*===========================================================================*/
+/* SDC driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Number of initialization attempts before rejecting the card.
+ * @note Attempts are performed at 10mS intervals.
+ */
+#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__)
+#define SDC_INIT_RETRY 100
+#endif
+
+/**
+ * @brief Include support for MMC cards.
+ * @note MMC support is not yet implemented so this option must be kept
+ * at @p FALSE.
+ */
+#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__)
+#define SDC_MMC_SUPPORT FALSE
+#endif
+
+/**
+ * @brief Delays insertions.
+ * @details If enabled this options inserts delays into the MMC waiting
+ * routines releasing some extra CPU time for the threads with
+ * lower priority, this may slow down the driver a bit however.
+ */
+#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__)
+#define SDC_NICE_WAITING TRUE
+#endif
+
+/*===========================================================================*/
+/* SERIAL driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Default bit rate.
+ * @details Configuration parameter, this is the baud rate selected for the
+ * default configuration.
+ */
+#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__)
+#define SERIAL_DEFAULT_BITRATE 38400
+#endif
+
+/**
+ * @brief Serial buffers size.
+ * @details Configuration parameter, you can change the depth of the queue
+ * buffers depending on the requirements of your application.
+ * @note The default is 64 bytes for both the transmission and receive
+ * buffers.
+ */
+#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__)
+#define SERIAL_BUFFERS_SIZE 16
+#endif
+
+/*===========================================================================*/
+/* SPI driver related settings. */
+/*===========================================================================*/
+
+/**
+ * @brief Enables synchronous APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__)
+#define SPI_USE_WAIT TRUE
+#endif
+
+/**
+ * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs.
+ * @note Disabling this option saves both code and data space.
+ */
+#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__)
+#define SPI_USE_MUTUAL_EXCLUSION TRUE
+#endif
+
+#endif /* _HALCONF_H_ */
+
+/** @} */
diff --git a/demos/ARMCM3-STM32F107-FATFS/main.c b/demos/ARMCM3-STM32F107-FATFS/main.c
new file mode 100644
index 000000000..c009b560a
--- /dev/null
+++ b/demos/ARMCM3-STM32F107-FATFS/main.c
@@ -0,0 +1,374 @@
+/*
+ ChibiOS/RT - Copyright (C) 2006,2007,2008,2009,2010,
+ 2011,2012 Giovanni Di Sirio.
+
+ This file is part of ChibiOS/RT.
+
+ ChibiOS/RT is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 3 of the License, or
+ (at your option) any later version.
+
+ ChibiOS/RT is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program. If not, see .
+*/
+
+#include
+
+#include "ch.h"
+#include "hal.h"
+#include "test.h"
+#include "shell.h"
+#include "evtimer.h"
+#include "chprintf.h"
+
+#include "ff.h"
+
+/*===========================================================================*/
+/* Card insertion monitor. */
+/*===========================================================================*/
+
+#define POLLING_INTERVAL 10
+#define POLLING_DELAY 10
+
+/**
+ * @brief Card monitor timer.
+ */
+static VirtualTimer tmr;
+
+/**
+ * @brief Debounce counter.
+ */
+static unsigned cnt;
+
+/**
+ * @brief Card event sources.
+ */
+static EventSource inserted_event, removed_event;
+
+/**
+ * @brief Insertion monitor timer callback function.
+ *
+ * @param[in] p pointer to the @p BaseBlockDevice object
+ *
+ * @notapi
+ */
+static void tmrfunc(void *p) {
+ BaseBlockDevice *bbdp = p;
+
+ chSysLockFromIsr();
+ if (cnt > 0) {
+ if (blkIsInserted(bbdp)) {
+ if (--cnt == 0) {
+ chEvtBroadcastI(&inserted_event);
+ }
+ }
+ else
+ cnt = POLLING_INTERVAL;
+ }
+ else {
+ if (!blkIsInserted(bbdp)) {
+ cnt = POLLING_INTERVAL;
+ chEvtBroadcastI(&removed_event);
+ }
+ }
+ chVTSetI(&tmr, MS2ST(POLLING_DELAY), tmrfunc, bbdp);
+ chSysUnlockFromIsr();
+}
+
+/**
+ * @brief Polling monitor start.
+ *
+ * @param[in] p pointer to an object implementing @p BaseBlockDevice
+ *
+ * @notapi
+ */
+static void tmr_init(void *p) {
+
+ chEvtInit(&inserted_event);
+ chEvtInit(&removed_event);
+ chSysLock();
+ cnt = POLLING_INTERVAL;
+ chVTSetI(&tmr, MS2ST(POLLING_DELAY), tmrfunc, p);
+ chSysUnlock();
+}
+
+/*===========================================================================*/
+/* FatFs related. */
+/*===========================================================================*/
+
+/**
+ * @brief FS object.
+ */
+FATFS MMC_FS;
+
+/**
+ * MMC driver instance.
+ */
+MMCDriver MMCD1;
+
+/* FS mounted and ready.*/
+static bool_t fs_ready = FALSE;
+
+/* Maximum speed SPI configuration (18MHz, CPHA=0, CPOL=0, MSb first).*/
+static SPIConfig hs_spicfg = {NULL, GPIOA, GPIOA_SPI3_CS_MMC, 0};
+
+/* Low speed SPI configuration (281.250kHz, CPHA=0, CPOL=0, MSb first).*/
+static SPIConfig ls_spicfg = {NULL, GPIOA, GPIOA_SPI3_CS_MMC,
+ SPI_CR1_BR_2 | SPI_CR1_BR_1};
+
+/* MMC/SD over SPI driver configuration.*/
+static MMCConfig mmccfg = {&SPID3, &ls_spicfg, &hs_spicfg};
+
+/* Generic large buffer.*/
+uint8_t fbuff[1024];
+
+static FRESULT scan_files(BaseSequentialStream *chp, char *path) {
+ FRESULT res;
+ FILINFO fno;
+ DIR dir;
+ int i;
+ char *fn;
+
+ res = f_opendir(&dir, path);
+ if (res == FR_OK) {
+ i = strlen(path);
+ for (;;) {
+ res = f_readdir(&dir, &fno);
+ if (res != FR_OK || fno.fname[0] == 0)
+ break;
+ if (fno.fname[0] == '.')
+ continue;
+ fn = fno.fname;
+ if (fno.fattrib & AM_DIR) {
+ path[i++] = '/';
+ strcpy(&path[i], fn);
+ res = scan_files(chp, path);
+ if (res != FR_OK)
+ break;
+ path[i] = 0;
+ }
+ else {
+ chprintf(chp, "%s/%s\r\n", path, fn);
+ }
+ }
+ }
+ return res;
+}
+
+/*===========================================================================*/
+/* Command line related. */
+/*===========================================================================*/
+
+#define SHELL_WA_SIZE THD_WA_SIZE(2048)
+#define TEST_WA_SIZE THD_WA_SIZE(256)
+
+static void cmd_mem(BaseSequentialStream *chp, int argc, char *argv[]) {
+ size_t n, size;
+
+ (void)argv;
+ if (argc > 0) {
+ chprintf(chp, "Usage: mem\r\n");
+ return;
+ }
+ n = chHeapStatus(NULL, &size);
+ chprintf(chp, "core free memory : %u bytes\r\n", chCoreStatus());
+ chprintf(chp, "heap fragments : %u\r\n", n);
+ chprintf(chp, "heap free total : %u bytes\r\n", size);
+}
+
+static void cmd_threads(BaseSequentialStream *chp, int argc, char *argv[]) {
+ static const char *states[] = {THD_STATE_NAMES};
+ Thread *tp;
+
+ (void)argv;
+ if (argc > 0) {
+ chprintf(chp, "Usage: threads\r\n");
+ return;
+ }
+ chprintf(chp, " addr stack prio refs state time\r\n");
+ tp = chRegFirstThread();
+ do {
+ chprintf(chp, "%.8lx %.8lx %4lu %4lu %9s %lu\r\n",
+ (uint32_t)tp, (uint32_t)tp->p_ctx.r13,
+ (uint32_t)tp->p_prio, (uint32_t)(tp->p_refs - 1),
+ states[tp->p_state], (uint32_t)tp->p_time);
+ tp = chRegNextThread(tp);
+ } while (tp != NULL);
+}
+
+static void cmd_test(BaseSequentialStream *chp, int argc, char *argv[]) {
+ Thread *tp;
+
+ (void)argv;
+ if (argc > 0) {
+ chprintf(chp, "Usage: test\r\n");
+ return;
+ }
+ tp = chThdCreateFromHeap(NULL, TEST_WA_SIZE, chThdGetPriority(),
+ TestThread, chp);
+ if (tp == NULL) {
+ chprintf(chp, "out of memory\r\n");
+ return;
+ }
+ chThdWait(tp);
+}
+
+static void cmd_tree(BaseSequentialStream *chp, int argc, char *argv[]) {
+ FRESULT err;
+ uint32_t clusters;
+ FATFS *fsp;
+
+ (void)argv;
+ if (argc > 0) {
+ chprintf(chp, "Usage: tree\r\n");
+ return;
+ }
+ if (!fs_ready) {
+ chprintf(chp, "File System not mounted\r\n");
+ return;
+ }
+ err = f_getfree("/", &clusters, &fsp);
+ if (err != FR_OK) {
+ chprintf(chp, "FS: f_getfree() failed\r\n");
+ return;
+ }
+ chprintf(chp,
+ "FS: %lu free clusters, %lu sectors per cluster, %lu bytes free\r\n",
+ clusters, (uint32_t)MMC_FS.csize,
+ clusters * (uint32_t)MMC_FS.csize * (uint32_t)MMC_SECTOR_SIZE);
+ fbuff[0] = 0;
+ scan_files(chp, (char *)fbuff);
+}
+
+static const ShellCommand commands[] = {
+ {"mem", cmd_mem},
+ {"threads", cmd_threads},
+ {"test", cmd_test},
+ {"tree", cmd_tree},
+ {NULL, NULL}
+};
+
+static const ShellConfig shell_cfg1 = {
+ (BaseSequentialStream *)&SD3,
+ commands
+};
+
+/*===========================================================================*/
+/* Main and generic code. */
+/*===========================================================================*/
+
+/*
+ * Red LEDs blinker thread, times are in milliseconds.
+ */
+static WORKING_AREA(waThread1, 128);
+static msg_t Thread1(void *arg) {
+
+ (void)arg;
+ chRegSetThreadName("blinker");
+ while (TRUE) {
+ palTogglePad(IOPORT3, GPIOC_LED_STATUS1);
+ chThdSleepMilliseconds(fs_ready ? 125 : 500);
+ }
+ return 0;
+}
+
+/*
+ * MMC card insertion event.
+ */
+static void InsertHandler(eventid_t id) {
+ FRESULT err;
+
+ (void)id;
+ /*
+ * On insertion MMC initialization and FS mount.
+ */
+ if (mmcConnect(&MMCD1)) {
+ return;
+ }
+ err = f_mount(0, &MMC_FS);
+ if (err != FR_OK) {
+ mmcDisconnect(&MMCD1);
+ return;
+ }
+ fs_ready = TRUE;
+}
+
+/*
+ * MMC card removal event.
+ */
+static void RemoveHandler(eventid_t id) {
+
+ (void)id;
+ fs_ready = FALSE;
+}
+
+/*
+ * Application entry point.
+ */
+int main(void) {
+ static const evhandler_t evhndl[] = {
+ InsertHandler,
+ RemoveHandler
+ };
+ Thread *shelltp = NULL;
+ struct EventListener el0, el1;
+
+ /*
+ * System initializations.
+ * - HAL initialization, this also initializes the configured device drivers
+ * and performs the board-specific initializations.
+ * - Kernel initialization, the main() function becomes a thread and the
+ * RTOS is active.
+ */
+ halInit();
+ chSysInit();
+
+ /*
+ * Activates the serial driver 2 using the driver default configuration.
+ */
+ sdStart(&SD3, NULL);
+
+ /*
+ * Shell manager initialization.
+ */
+ shellInit();
+
+ /*
+ * Initializes the MMC driver to work with SPI2.
+ */
+ mmcObjectInit(&MMCD1);
+ mmcStart(&MMCD1, &mmccfg);
+
+ /*
+ * Activates the card insertion monitor.
+ */
+ tmr_init(&MMCD1);
+
+ /*
+ * Creates the blinker thread.
+ */
+ chThdCreateStatic(waThread1, sizeof(waThread1), NORMALPRIO, Thread1, NULL);
+
+ /*
+ * Normal main() thread activity, in this demo it does nothing except
+ * sleeping in a loop and listen for events.
+ */
+ chEvtRegister(&inserted_event, &el0, 0);
+ chEvtRegister(&removed_event, &el1, 1);
+ while (TRUE) {
+ if (!shelltp)
+ shelltp = shellCreate(&shell_cfg1, SHELL_WA_SIZE, NORMALPRIO);
+ else if (chThdTerminated(shelltp)) {
+ chThdRelease(shelltp); /* Recovers memory of the previous shell. */
+ shelltp = NULL; /* Triggers spawning of a new shell. */
+ }
+ chEvtDispatch(evhndl, chEvtWaitOne(ALL_EVENTS));
+ }
+ return 0;
+}
diff --git a/demos/ARMCM3-STM32F107-FATFS/mcuconf.h b/demos/ARMCM3-STM32F107-FATFS/mcuconf.h
new file mode 100644
index 000000000..d2bfe99a5
--- /dev/null
+++ b/demos/ARMCM3-STM32F107-FATFS/mcuconf.h
@@ -0,0 +1,211 @@
+/*
+ ChibiOS/RT - Copyright (C) 2006,2007,2008,2009,2010,
+ 2011,2012 Giovanni Di Sirio.
+
+ This file is part of ChibiOS/RT.
+
+ ChibiOS/RT is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 3 of the License, or
+ (at your option) any later version.
+
+ ChibiOS/RT is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program. If not, see .
+*/
+
+/*
+ * STM32F1xx drivers configuration.
+ * The following settings override the default settings present in
+ * the various device driver implementation headers.
+ * Note that the settings for each driver only have effect if the whole
+ * driver is enabled in halconf.h.
+ *
+ * IRQ priorities:
+ * 15...0 Lowest...Highest.
+ *
+ * DMA priorities:
+ * 0...3 Lowest...Highest.
+ */
+
+/*
+ * HAL driver system settings.
+ */
+#define STM32_NO_INIT FALSE
+#define STM32_HSI_ENABLED TRUE
+#define STM32_LSI_ENABLED FALSE
+#define STM32_HSE_ENABLED TRUE
+#define STM32_LSE_ENABLED FALSE
+#define STM32_SW STM32_SW_PLL
+#define STM32_PLLSRC STM32_PLLSRC_PREDIV1
+#define STM32_PREDIV1SRC STM32_PREDIV1SRC_PLL2
+#define STM32_PREDIV1_VALUE 5
+#define STM32_PLLMUL_VALUE 9
+#define STM32_PREDIV2_VALUE 5
+#define STM32_PLL2MUL_VALUE 8
+#define STM32_PLL3MUL_VALUE 10
+#define STM32_HPRE STM32_HPRE_DIV1
+#define STM32_PPRE1 STM32_PPRE1_DIV2
+#define STM32_PPRE2 STM32_PPRE2_DIV2
+#define STM32_ADCPRE STM32_ADCPRE_DIV4
+#define STM32_OTG_CLOCK_REQUIRED TRUE
+#define STM32_OTGFSPRE STM32_OTGFSPRE_DIV3
+#define STM32_I2S_CLOCK_REQUIRED FALSE
+#define STM32_MCOSEL STM32_MCOSEL_PLL3
+#define STM32_RTCSEL STM32_RTCSEL_HSEDIV
+#define STM32_PVD_ENABLE FALSE
+#define STM32_PLS STM32_PLS_LEV0
+
+/*
+ * ADC driver system settings.
+ */
+#define STM32_ADC_USE_ADC1 TRUE
+#define STM32_ADC_ADC1_DMA_PRIORITY 2
+#define STM32_ADC_ADC1_IRQ_PRIORITY 5
+
+/*
+ * CAN driver system settings.
+ */
+#define STM32_CAN_USE_CAN1 TRUE
+#define STM32_CAN_CAN1_IRQ_PRIORITY 11
+
+/*
+ * EXT driver system settings.
+ */
+#define STM32_EXT_EXTI0_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI1_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI2_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI3_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI4_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI16_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI17_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI18_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI19_IRQ_PRIORITY 6
+
+/*
+ * GPT driver system settings.
+ */
+#define STM32_GPT_USE_TIM1 FALSE
+#define STM32_GPT_USE_TIM2 FALSE
+#define STM32_GPT_USE_TIM3 FALSE
+#define STM32_GPT_USE_TIM4 FALSE
+#define STM32_GPT_USE_TIM5 FALSE
+#define STM32_GPT_USE_TIM8 FALSE
+#define STM32_GPT_TIM1_IRQ_PRIORITY 7
+#define STM32_GPT_TIM2_IRQ_PRIORITY 7
+#define STM32_GPT_TIM3_IRQ_PRIORITY 7
+#define STM32_GPT_TIM4_IRQ_PRIORITY 7
+#define STM32_GPT_TIM5_IRQ_PRIORITY 7
+#define STM32_GPT_TIM8_IRQ_PRIORITY 7
+
+/*
+ * I2C driver system settings.
+ */
+#define STM32_I2C_USE_I2C1 FALSE
+#define STM32_I2C_USE_I2C2 FALSE
+#define STM32_I2C_USE_I2C3 FALSE
+#define STM32_I2C_I2C1_IRQ_PRIORITY 10
+#define STM32_I2C_I2C2_IRQ_PRIORITY 10
+#define STM32_I2C_I2C3_IRQ_PRIORITY 10
+#define STM32_I2C_I2C1_DMA_PRIORITY 1
+#define STM32_I2C_I2C2_DMA_PRIORITY 1
+#define STM32_I2C_I2C3_DMA_PRIORITY 1
+#define STM32_I2C_I2C1_DMA_ERROR_HOOK() chSysHalt()
+#define STM32_I2C_I2C2_DMA_ERROR_HOOK() chSysHalt()
+#define STM32_I2C_I2C3_DMA_ERROR_HOOK() chSysHalt()
+
+/*
+ * ICU driver system settings.
+ */
+#define STM32_ICU_USE_TIM1 FALSE
+#define STM32_ICU_USE_TIM2 FALSE
+#define STM32_ICU_USE_TIM3 FALSE
+#define STM32_ICU_USE_TIM4 FALSE
+#define STM32_ICU_USE_TIM5 FALSE
+#define STM32_ICU_USE_TIM8 FALSE
+#define STM32_ICU_TIM1_IRQ_PRIORITY 7
+#define STM32_ICU_TIM2_IRQ_PRIORITY 7
+#define STM32_ICU_TIM3_IRQ_PRIORITY 7
+#define STM32_ICU_TIM4_IRQ_PRIORITY 7
+#define STM32_ICU_TIM5_IRQ_PRIORITY 7
+#define STM32_ICU_TIM8_IRQ_PRIORITY 7
+
+/*
+ * PWM driver system settings.
+ */
+#define STM32_PWM_USE_ADVANCED FALSE
+#define STM32_PWM_USE_TIM1 FALSE
+#define STM32_PWM_USE_TIM2 FALSE
+#define STM32_PWM_USE_TIM3 FALSE
+#define STM32_PWM_USE_TIM4 FALSE
+#define STM32_PWM_USE_TIM5 FALSE
+#define STM32_PWM_USE_TIM8 FALSE
+#define STM32_PWM_TIM1_IRQ_PRIORITY 7
+#define STM32_PWM_TIM2_IRQ_PRIORITY 7
+#define STM32_PWM_TIM3_IRQ_PRIORITY 7
+#define STM32_PWM_TIM4_IRQ_PRIORITY 7
+#define STM32_PWM_TIM5_IRQ_PRIORITY 7
+#define STM32_PWM_TIM8_IRQ_PRIORITY 7
+
+/*
+ * RTC driver system settings.
+ */
+#define STM32_RTC_IRQ_PRIORITY 15
+
+/*
+ * SERIAL driver system settings.
+ */
+#define STM32_SERIAL_USE_USART1 FALSE
+#define STM32_SERIAL_USE_USART2 FALSE
+#define STM32_SERIAL_USE_USART3 TRUE
+#define STM32_SERIAL_USE_UART4 FALSE
+#define STM32_SERIAL_USE_UART5 FALSE
+#define STM32_SERIAL_USE_USART6 FALSE
+#define STM32_SERIAL_USART1_PRIORITY 12
+#define STM32_SERIAL_USART2_PRIORITY 12
+#define STM32_SERIAL_USART3_PRIORITY 12
+#define STM32_SERIAL_UART4_PRIORITY 12
+#define STM32_SERIAL_UART5_PRIORITY 12
+#define STM32_SERIAL_USART6_PRIORITY 12
+
+/*
+ * SPI driver system settings.
+ */
+#define STM32_SPI_USE_SPI1 FALSE
+#define STM32_SPI_USE_SPI2 FALSE
+#define STM32_SPI_USE_SPI3 TRUE
+#define STM32_SPI_SPI1_DMA_PRIORITY 1
+#define STM32_SPI_SPI2_DMA_PRIORITY 1
+#define STM32_SPI_SPI3_DMA_PRIORITY 1
+#define STM32_SPI_SPI1_IRQ_PRIORITY 10
+#define STM32_SPI_SPI2_IRQ_PRIORITY 10
+#define STM32_SPI_SPI3_IRQ_PRIORITY 10
+#define STM32_SPI_DMA_ERROR_HOOK(spip) chSysHalt()
+
+/*
+ * UART driver system settings.
+ */
+#define STM32_UART_USE_USART1 FALSE
+#define STM32_UART_USE_USART2 FALSE
+#define STM32_UART_USE_USART3 FALSE
+#define STM32_UART_USART1_IRQ_PRIORITY 12
+#define STM32_UART_USART2_IRQ_PRIORITY 12
+#define STM32_UART_USART3_IRQ_PRIORITY 12
+#define STM32_UART_USART1_DMA_PRIORITY 0
+#define STM32_UART_USART2_DMA_PRIORITY 0
+#define STM32_UART_USART3_DMA_PRIORITY 0
+#define STM32_UART_DMA_ERROR_HOOK(uartp) chSysHalt()
+
+/*
+ * USB driver system settings.
+ */
+#define STM32_USB_USE_USB1 TRUE
+#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE
+#define STM32_USB_USB1_HP_IRQ_PRIORITY 13
+#define STM32_USB_USB1_LP_IRQ_PRIORITY 14
diff --git a/demos/ARMCM3-STM32F107-FATFS/readme.txt b/demos/ARMCM3-STM32F107-FATFS/readme.txt
new file mode 100644
index 000000000..bf9d03077
--- /dev/null
+++ b/demos/ARMCM3-STM32F107-FATFS/readme.txt
@@ -0,0 +1,33 @@
+*****************************************************************************
+** ChibiOS/RT port for ARM-Cortex-M3 STM32F107. **
+*****************************************************************************
+
+** TARGET **
+
+The demo runs on an Olimex STM32-P107 board.
+
+** The Demo **
+
+This demo shows how to integrate the FatFs file system and use the SPI and MMC
+drivers.
+The demo flashes the board LED using a thread and monitors the MMC slot for
+a card insertion. When a card is inserted then the file system is mounted
+and the LED flashes faster.
+A command line shell is spawned on SD3, all the interaction with the demo is
+performed using the command shell, type "help" for a list of the available
+commands.
+
+** Build Procedure **
+
+The demo has been tested by using the free Codesourcery GCC-based toolchain,
+YAGARTO and an experimental WinARM build including GCC 4.3.0.
+Just modify the TRGT line in the makefile in order to use different GCC ports.
+
+** Notes **
+
+Some files used by the demo are not part of ChibiOS/RT but are copyright of
+ST Microelectronics and are licensed under a different license.
+Also note that not all the files present in the ST library are distributed
+with ChibiOS/RT, you can find the whole library on the ST web site:
+
+ http://www.st.com
diff --git a/readme.txt b/readme.txt
index 9fea67c80..9924dba38 100644
--- a/readme.txt
+++ b/readme.txt
@@ -161,6 +161,7 @@
3484947)(backported to 2.4.1).
- FIX: Fixed various minor documentation errors (bug 3484942)(backported
to 2.4.1).
+- NEW: Added FatFs demo for the Olimex STM32-P107 board.
- NEW: Added support for the Olimex STM32-E407 board. Added an integrated
demo including USB-CDC, lwIP with web server, FatFs and shell, all running
together.