tinySA/os/hal/platforms/STM32/i2c_lld.c

/**
 * @file STM32/i2c_lld.c
 * @brief STM32 I2C subsystem low level driver source. Slave mode not implemented.
 * @addtogroup STM32_I2C
 * @{
 */

#include "ch.h"
#include "hal.h"
#include "i2c_lld.h"

#if HAL_USE_I2C || defined(__DOXYGEN__)

/*===========================================================================*/
/* Driver exported variables.                                                */
/*===========================================================================*/

/** @brief I2C1 driver identifier.*/
#if STM32_I2C_USE_I2C1 || defined(__DOXYGEN__)
I2CDriver I2CD1;
#endif

/** @brief I2C2 driver identifier.*/
#if STM32_I2C_USE_I2C2 || defined(__DOXYGEN__)
I2CDriver I2CD2;
#endif

/*===========================================================================*/
/* Driver local variables.                                                   */
/*===========================================================================*/

/*===========================================================================*/
/* Driver local functions.                                                   */
/*===========================================================================*/


static uint32_t i2c_get_event(I2CDriver *i2cp){
  uint32_t regSR1 = i2cp->id_i2c->SR1;
  uint32_t regSR2 = i2cp->id_i2c->SR2;
  /* return the last event value from I2C status registers */
  return (I2C_EV_MASK & (regSR1 | (regSR2 << 16)));
}

static void i2c_serve_event_interrupt(I2CDriver *i2cp) {
  static __IO uint8_t *txBuffp, *rxBuffp, *datap;

  I2C_TypeDef *dp = i2cp->id_i2c;

  switch(i2c_get_event(i2cp)) {
  case I2C_EV5_MASTER_MODE_SELECT:
    i2cp->id_slave_config->flags &= ~I2C_FLG_HEADER_SENT;
    dp->DR = i2cp->slave_addr1;
    break;
  case I2C_EV9_MASTER_ADDR_10BIT:
    if(i2cp->id_slave_config->flags & I2C_FLG_MASTER_RECEIVER) {
      i2cp->slave_addr1 |= 0x01;
      i2cp->id_slave_config->flags |= I2C_FLG_HEADER_SENT;
//      i2cp->id_i2c->CR1 = (i2cp->id_i2c->CR1 & (~I2C_CR1_ACK)) | I2C_CR1_STOP;
    }
    dp->DR = i2cp->slave_addr2;
    break;


  //------------------------------------------------------------------------
  // Master Transmitter ----------------------------------------------------
  //------------------------------------------------------------------------
  case I2C_EV6_MASTER_TRA_MODE_SELECTED:
    if(i2cp->id_slave_config->flags & I2C_FLG_HEADER_SENT){
      dp->CR1 |= I2C_CR1_START;               // re-send the start in 10-Bit address mode
      break;
    }
    //Initialize the transmit buffer pointer
    txBuffp = (uint8_t*)i2cp->id_slave_config->txbuf;
    datap = txBuffp;
    txBuffp++;
    i2cp->id_slave_config->txbytes--;
    /* If no further data to be sent, disable the I2C ITBUF in order to not have a TxE interrupt */
    if(i2cp->id_slave_config->txbytes == 0) {
      dp->CR2 &= (uint16_t)~I2C_CR2_ITBUFEN;
    }
    //EV8_1 write the first data
    dp->DR = *datap;
    break;
  case I2C_EV8_MASTER_BYTE_TRANSMITTING:
    if(i2cp->id_slave_config->txbytes > 0) {
      datap = txBuffp;
      txBuffp++;
      i2cp->id_slave_config->txbytes--;
      if(i2cp->id_slave_config->txbytes == 0) {
        /* If no further data to be sent, disable the ITBUF in order to not have a TxE interrupt */
        dp->CR2 &= (uint16_t)~I2C_CR2_ITBUFEN;
      }
      dp->DR = *datap;
    }
    break;
  case I2C_EV8_2_MASTER_BYTE_TRANSMITTED:
    /* if nothing to read then generate stop */
    if (i2cp->id_slave_config->rxbytes == 0){
      dp->CR1 |= I2C_CR1_STOP;   // stop generation
      /* Disable ITEVT In order to not have again a BTF IT */
      dp->CR2 &= (uint16_t)~I2C_CR2_ITEVTEN;
      /* Portable I2C ISR code defined in the high level driver, note, it is a macro.*/
      _i2c_isr_code(i2cp, i2cp->id_slave_config);
    }
    else{
      /* Disable ITEVT In order to not have again a BTF IT */
      dp->CR2 &= (uint16_t)~I2C_CR2_ITEVTEN;
      /* send restart and begin reading operations */
      i2c_lld_master_receive(i2cp);
    }
    break;


  //------------------------------------------------------------------------
  // Master Receiver -------------------------------------------------------
  //------------------------------------------------------------------------
  case I2C_EV6_MASTER_REC_MODE_SELECTED:
    chSysLockFromIsr();
    switch(i2cp->id_slave_config->flags & EV6_SUBEV_MASK) {
    case I2C_EV6_3_MASTER_REC_1BTR_MODE_SELECTED: // only an single byte to receive
      /* Clear ACK */
      dp->CR1 &= (uint16_t)~I2C_CR1_ACK;
      /* Program the STOP */
      dp->CR1 |= I2C_CR1_STOP;
      break;
    case I2C_EV6_1_MASTER_REC_2BTR_MODE_SELECTED: // only two bytes to receive
      /* Clear ACK */
      dp->CR1 &= (uint16_t)~I2C_CR1_ACK;
      /* Disable the ITBUF in order to have only the BTF interrupt */
      dp->CR2 &= (uint16_t)~I2C_CR2_ITBUFEN;
      break;
    }
    chSysUnlockFromIsr();
    /* Initialize receive buffer pointer */
    rxBuffp = i2cp->id_slave_config->rxbuf;
    break;
  case I2C_EV7_MASTER_REC_BYTE_RECEIVED:
    if(i2cp->id_slave_config->rxbytes != 3) {
      /* Read the data register */
      *rxBuffp = dp->DR;
      rxBuffp++;
      i2cp->id_slave_config->rxbytes--;
      switch(i2cp->id_slave_config->rxbytes){
      case 3:
        /* Disable the ITBUF in order to have only the BTF interrupt */
        dp->CR2 &= (uint16_t)~I2C_CR2_ITBUFEN;
        i2cp->id_slave_config->flags |= I2C_FLG_3BTR;
        break;
      case 0:
        /* Portable I2C ISR code defined in the high level driver, note, it is a macro.*/
        _i2c_isr_code(i2cp, i2cp->id_slave_config);
        break;
      }
    }
    // when remaining 3 bytes do nothing, wait until RXNE and BTF are set (until 2 bytes are received)
    break;
  case I2C_EV7_MASTER_REC_BYTE_QUEUED:
    switch(i2cp->id_slave_config->flags & EV7_SUBEV_MASK) {
    case I2C_EV7_2_MASTER_REC_3BYTES_TO_PROCESS:
      // DataN-2 and DataN-1 are received
      chSysLockFromIsr();
      dp->CR2 |= I2C_CR2_ITBUFEN;
      /* Clear ACK */
      dp->CR1 &= (uint16_t)~I2C_CR1_ACK;
      /* Read the DataN-2*/
      *rxBuffp = dp->DR; //This clear the RXE & BFT flags and launch the DataN reception in the shift register (ending the SCL stretch)
      rxBuffp++;
      /* Program the STOP */
      dp->CR1 |= I2C_CR1_STOP;
      /* Read the DataN-1 */
      *rxBuffp = dp->DR;
      chSysUnlockFromIsr();
      rxBuffp++;
      /* Decrement the number of readed bytes */
      i2cp->id_slave_config->rxbytes -= 2;
      i2cp->id_slave_config->flags = 0;
      // ready for read DataN on the next EV7
      break;
    case I2C_EV7_3_MASTER_REC_2BYTES_TO_PROCESS: // only for case of two bytes to be received
      // DataN-1 and DataN are received
      chSysLockFromIsr();
      /* Program the STOP */
      dp->CR1 |= I2C_CR1_STOP;
      /* Read the DataN-1*/
      *rxBuffp = dp->DR;
      chSysUnlockFromIsr();
      rxBuffp++;
      /* Read the DataN*/
      *rxBuffp = dp->DR;
      i2cp->id_slave_config->rxbytes = 0;
      i2cp->id_slave_config->flags = 0;
      /* Portable I2C ISR code defined in the high level driver, note, it is a macro.*/
      _i2c_isr_code(i2cp, i2cp->id_slave_config);
      break;
    }
    break;
  }
}

static void i2c_serve_error_interrupt(I2CDriver *i2cp) {
  i2cflags_t flags;
  I2C_TypeDef *reg;

  reg = i2cp->id_i2c;
  flags = I2CD_NO_ERROR;

  if(reg->SR1 & I2C_SR1_BERR) {                // Bus error
    reg->SR1 &= ~I2C_SR1_BERR;
    flags |= I2CD_BUS_ERROR;
  }
  if(reg->SR1 & I2C_SR1_ARLO) {                // Arbitration lost
    reg->SR1 &= ~I2C_SR1_ARLO;
    flags |= I2CD_ARBITRATION_LOST;
  }
  if(reg->SR1 & I2C_SR1_AF) {                  // Acknowledge fail
    reg->SR1 &= ~I2C_SR1_AF;
    reg->CR1 |= I2C_CR1_STOP;                   // setting stop bit
    flags |= I2CD_ACK_FAILURE;
  }
  if(reg->SR1 & I2C_SR1_OVR) {                 // Overrun
    reg->SR1 &= ~I2C_SR1_OVR;
    flags |= I2CD_OVERRUN;
  }
  if(reg->SR1 & I2C_SR1_PECERR) {              // PEC error
    reg->SR1 &= ~I2C_SR1_PECERR;
    flags |= I2CD_PEC_ERROR;
  }
  if(reg->SR1 & I2C_SR1_TIMEOUT) {             // SMBus Timeout
    reg->SR1 &= ~I2C_SR1_TIMEOUT;
    flags |= I2CD_TIMEOUT;
  }
  if(reg->SR1 & I2C_SR1_SMBALERT) {            // SMBus alert
    reg->SR1 &= ~I2C_SR1_SMBALERT;
    flags |= I2CD_SMB_ALERT;
  }

  if(flags != I2CD_NO_ERROR) {
    // send communication end signal
    _i2c_isr_code(i2cp, i2cp->id_slave_config);
    chSysLockFromIsr();
    i2cAddFlagsI(i2cp, flags);
    chSysUnlockFromIsr();
  }
}


#if STM32_I2C_USE_I2C1 || defined(__DOXYGEN__)
/**
 * @brief I2C1 event interrupt handler.
 */
CH_IRQ_HANDLER(VectorBC) {

  CH_IRQ_PROLOGUE();
  i2c_serve_event_interrupt(&I2CD1);
  CH_IRQ_EPILOGUE();
}

/**
 * @brief I2C1 error interrupt handler.
 */
CH_IRQ_HANDLER(VectorC0) {

  CH_IRQ_PROLOGUE();
  i2c_serve_error_interrupt(&I2CD1);
  CH_IRQ_EPILOGUE();
}
#endif

#if STM32_I2C_USE_I2C2 || defined(__DOXYGEN__)
/**
 * @brief I2C2 event interrupt handler.
 */
CH_IRQ_HANDLER(VectorC4) {

  CH_IRQ_PROLOGUE();
  i2c_serve_event_interrupt(&I2CD2);
  CH_IRQ_EPILOGUE();
}

/**
 * @brief I2C2 error interrupt handler.
 */
CH_IRQ_HANDLER(VectorC8) {

  CH_IRQ_PROLOGUE();
  i2c_serve_error_interrupt(&I2CD2);
  CH_IRQ_EPILOGUE();
}
#endif

/**
 * @brief Low level I2C driver initialization.
 */
void i2c_lld_init(void) {

#if STM32_I2C_USE_I2C1
  RCC->APB1RSTR     = RCC_APB1RSTR_I2C1RST;           // reset I2C 1
  RCC->APB1RSTR     = 0;
  i2cObjectInit(&I2CD1);
  I2CD1.id_i2c     = I2C1;
#endif

#if STM32_I2C_USE_I2C2
  RCC->APB1RSTR     = RCC_APB1RSTR_I2C2RST;           // reset I2C 2
  RCC->APB1RSTR     = 0;
  i2cObjectInit(&I2CD2);
  I2CD2.id_i2c     = I2C2;
#endif
}

/**
 * @brief Configures and activates the I2C peripheral.
 *
 * @param[in] i2cp      pointer to the @p I2CDriver object
 */
void i2c_lld_start(I2CDriver *i2cp) {

  /* If in stopped state then enables the I2C clock.*/
  if (i2cp->id_state == I2C_STOP) {
#if STM32_I2C_USE_I2C1
    if (&I2CD1 == i2cp) {
      NVICEnableVector(I2C1_EV_IRQn, STM32_I2C_I2C1_IRQ_PRIORITY);
      NVICEnableVector(I2C1_ER_IRQn, STM32_I2C_I2C1_IRQ_PRIORITY);
      RCC->APB1ENR |= RCC_APB1ENR_I2C1EN; // I2C 1 clock enable
    }
#endif
#if STM32_I2C_USE_I2C2
    if (&I2CD2 == i2cp) {
      NVICEnableVector(I2C2_EV_IRQn, STM32_I2C_I2C2_IRQ_PRIORITY);
      NVICEnableVector(I2C2_ER_IRQn, STM32_I2C_I2C2_IRQ_PRIORITY);
      RCC->APB1ENR |= RCC_APB1ENR_I2C2EN; // I2C 2 clock enable
    }
#endif
  }

  /* I2C setup.*/
  i2cp->id_i2c->CR1 = I2C_CR1_SWRST; // reset i2c peripherial
  i2cp->id_i2c->CR1 = 0;

  i2c_lld_set_clock(i2cp);
  i2c_lld_set_opmode(i2cp);
  i2cp->id_i2c->CR2 |= I2C_CR2_ITERREN | I2C_CR2_ITEVTEN | I2C_CR2_ITBUFEN;// enable interrupts
  i2cp->id_i2c->CR1 |= 1; // enable interface
}

void i2c_lld_reset(I2CDriver *i2cp){
  chDbgCheck((i2cp->id_state == I2C_STOP)||(i2cp->id_state == I2C_READY),
             "i2c_lld_reset: invalid state");

  RCC->APB1RSTR     = RCC_APB1RSTR_I2C1RST;           // reset I2C 1
  RCC->APB1RSTR     = 0;
}


/**
 * @brief Set clock speed.
 *
 * @param[in] i2cp      pointer to the @p I2CDriver object
 */
void i2c_lld_set_clock(I2CDriver *i2cp) {
  volatile uint16_t regCCR, regCR2, freq, clock_div;
  volatile uint16_t pe_bit_saved;
  int32_t clock_speed = i2cp->id_config->clock_speed;
  i2cdutycycle_t duty = i2cp->id_config->duty_cycle;

  chDbgCheck((i2cp != NULL) && (clock_speed > 0) && (clock_speed <= 4000000),
             "i2c_lld_set_clock");

  /*---------------------------- CR2 Configuration ------------------------*/
  /* Get the I2Cx CR2 value */
  regCR2 = i2cp->id_i2c->CR2;

  /* Clear frequency FREQ[5:0] bits */
  regCR2 &= (uint16_t)~I2C_CR2_FREQ;
  /* Set frequency bits depending on pclk1 value */
  freq = (uint16_t)(STM32_PCLK1 / 1000000);
  chDbgCheck((freq >= 2) && (freq <= 36),
              "i2c_lld_set_clock() : Peripheral clock freq. out of range");
  regCR2 |= freq;
  i2cp->id_i2c->CR2 = regCR2;

  /*---------------------------- CCR Configuration ------------------------*/
  pe_bit_saved = (i2cp->id_i2c->CR1 & I2C_CR1_PE);
  /* Disable the selected I2C peripheral to configure TRISE */
  i2cp->id_i2c->CR1 &= (uint16_t)~I2C_CR1_PE;

  /* Clear F/S, DUTY and CCR[11:0] bits */
  regCCR = 0;
  clock_div = I2C_CCR_CCR;
  /* Configure clock_div in standard mode */
  if (clock_speed <= 100000) {
    chDbgAssert(duty == STD_DUTY_CYCLE,
                "i2c_lld_set_clock(), #1", "Invalid standard mode duty cycle");
    /* Standard mode clock_div calculate: Tlow/Thigh = 1/1 */
    clock_div = (uint16_t)(STM32_PCLK1 / (clock_speed * 2));
    /* Test if CCR value is under 0x4, and set the minimum allowed value */
    if (clock_div < 0x04) clock_div = 0x04;
    /* Set clock_div value for standard mode */
    regCCR |= (clock_div & I2C_CCR_CCR);
    /* Set Maximum Rise Time for standard mode */
    i2cp->id_i2c->TRISE = freq + 1;
  }
  /* Configure clock_div in fast mode */
  else if(clock_speed <= 400000) {
    chDbgAssert((duty == FAST_DUTY_CYCLE_2) || (duty == FAST_DUTY_CYCLE_16_9),
                "i2c_lld_set_clock(), #2", "Invalid fast mode duty cycle");
    if(duty == FAST_DUTY_CYCLE_2) {
      /* Fast mode clock_div calculate: Tlow/Thigh = 2/1 */
      clock_div = (uint16_t)(STM32_PCLK1 / (clock_speed * 3));
    }
    else if(duty == FAST_DUTY_CYCLE_16_9) {
      /* Fast mode clock_div calculate: Tlow/Thigh = 16/9 */
      clock_div = (uint16_t)(STM32_PCLK1 / (clock_speed * 25));
      /* Set DUTY bit */
      regCCR |= I2C_CCR_DUTY;
    }
    /* Test if CCR value is under 0x1, and set the minimum allowed value */
    if(clock_div < 0x01) clock_div = 0x01;
    /* Set clock_div value and F/S bit for fast mode*/
    regCCR |= (I2C_CCR_FS | (clock_div & I2C_CCR_CCR));
    /* Set Maximum Rise Time for fast mode */
    i2cp->id_i2c->TRISE = (freq * 300 / 1000) + 1;
  }
  chDbgAssert((clock_div <= I2C_CCR_CCR),
      "i2c_lld_set_clock(), #3", "Too low clock clock speed selected");

  /* Write to I2Cx CCR */
  i2cp->id_i2c->CCR = regCCR;

  /* restore the I2C peripheral enabled state */
  i2cp->id_i2c->CR1 |= pe_bit_saved;
}

/**
 * @brief Set operation mode of I2C hardware.
 *
 * @param[in] i2cp      pointer to the @p I2CDriver object
 */
void i2c_lld_set_opmode(I2CDriver *i2cp) {
  i2copmode_t opmode = i2cp->id_config->op_mode;
  uint16_t regCR1;

  /*---------------------------- CR1 Configuration ------------------------*/
  /* Get the I2Cx CR1 value */
  regCR1 = i2cp->id_i2c->CR1;
  switch(opmode){
  case OPMODE_I2C:
    regCR1 &= (uint16_t)~(I2C_CR1_SMBUS|I2C_CR1_SMBTYPE);
    break;
  case OPMODE_SMBUS_DEVICE:
    regCR1 |= I2C_CR1_SMBUS;
    regCR1 &= (uint16_t)~(I2C_CR1_SMBTYPE);
    break;
  case OPMODE_SMBUS_HOST:
    regCR1 |= (I2C_CR1_SMBUS|I2C_CR1_SMBTYPE);
    break;
  }
  /* Write to I2Cx CR1 */
  i2cp->id_i2c->CR1 = regCR1;
}

/**
 * @brief Set own address.
 *
 * @param[in] i2cp      pointer to the @p I2CDriver object
 */
void i2c_lld_set_own_address(I2CDriver *i2cp) {
  //TODO: dual address mode

  /*---------------------------- OAR1 Configuration -----------------------*/
  i2cp->id_i2c->OAR1 |= 1 << 14;

  if (&(i2cp->id_config->own_addr_10) == NULL){// only 7-bit address
    i2cp->id_i2c->OAR1 &= (~I2C_OAR1_ADDMODE);
    i2cp->id_i2c->OAR1 |= i2cp->id_config->own_addr_7 << 1;
  }
  else {
    chDbgAssert((i2cp->id_config->own_addr_10 < 1024),
        "i2c_lld_set_own_address(), #1", "10-bit address longer then 10 bit")
    i2cp->id_i2c->OAR1 |= I2C_OAR1_ADDMODE;
    i2cp->id_i2c->OAR1 |= i2cp->id_config->own_addr_10;
  }
}


/**
 * @brief Deactivates the I2C peripheral.
 *
 * @param[in] i2cp      pointer to the @p I2CDriver object
 */
void i2c_lld_stop(I2CDriver *i2cp) {

  /* If in ready state then disables the I2C clock.*/
  if (i2cp->id_state == I2C_READY) {
#if STM32_I2C_USE_I2C1
    if (&I2CD1 == i2cp) {
      NVICDisableVector(I2C1_EV_IRQn);
      NVICDisableVector(I2C1_ER_IRQn);
      RCC->APB1ENR &= ~RCC_APB1ENR_I2C1EN;
    }
#endif
#if STM32_I2C_USE_I2C2
    if (&I2CD2 == i2cp) {
      NVICDisableVector(I2C2_EV_IRQn);
      NVICDisableVector(I2C2_ER_IRQn);
      RCC->APB1ENR &= ~RCC_APB1ENR_I2C2EN;
    }
#endif
  }
  i2cp->id_state = I2C_STOP;
}

/**
 * @brief Transmits data ever the I2C bus as master.
 *
 * @param[in] i2cp          pointer to the @p I2CDriver object
 *
 */
void i2c_lld_master_transmit(I2CDriver *i2cp) {

  // enable ERR, EVT & BUF ITs
  i2cp->id_i2c->CR2 |= (I2C_CR2_ITERREN|I2C_CR2_ITEVTEN|I2C_CR2_ITBUFEN);
  i2cp->id_i2c->CR1 &= ~I2C_CR1_POS;

  switch(i2cp->id_slave_config->nbit_addr){
  case 7:
    // LSB = 0 -> write
    i2cp->slave_addr1 = ((i2cp->id_slave_config->slave_addr <<1) & 0x00FE);
    break;
  case 10:
    // add the two msb of 10-bit address to the header
    i2cp->slave_addr1 = ((i2cp->id_slave_config->slave_addr >>7) & 0x0006);
    // add the header bits with LSB = 0 -> write
    i2cp->slave_addr1 |= 0xF0;
    // the remaining 8 bit of 10-bit address
    i2cp->slave_addr2 = i2cp->id_slave_config->slave_addr & 0x00FF;
    break;
  }

  i2cp->id_slave_config->flags = 0;
  i2cp->id_slave_config->errors = 0;

  i2cp->id_i2c->CR1 |= I2C_CR1_START;               // send start bit

#if !I2C_USE_WAIT
  /* Wait until the START condition is generated on the bus:
   * the START bit is cleared by hardware */
  uint32_t timeout = 0xfffff;
  while((i2cp->id_i2c->CR1 & I2C_CR1_START) && timeout--)
    ;
#endif /* I2C_USE_WAIT */
}


/**
 * @brief Receives data from the I2C bus.
 *
 * @param[in] i2cp          pointer to the @p I2CDriver object
 *
 */
void i2c_lld_master_receive(I2CDriver *i2cp){
  // enable ERR, EVT & BUF ITs
  i2cp->id_i2c->CR2 |= (I2C_CR2_ITERREN|I2C_CR2_ITEVTEN|I2C_CR2_ITBUFEN);
  i2cp->id_i2c->CR1 |= I2C_CR1_ACK;                 // acknowledge returned
  i2cp->id_i2c->CR1 &= ~I2C_CR1_POS;

  switch(i2cp->id_slave_config->nbit_addr){
  case 7:
    // LSB = 1 -> receive
    i2cp->slave_addr1 = ((i2cp->id_slave_config->slave_addr <<1) | 0x01);
    break;
  case 10:
    // add the two msb of 10-bit address to the header
    i2cp->slave_addr1 = ((i2cp->id_slave_config->slave_addr >>7) & 0x0006);
    // add the header bits (the LSB -> 1 will be add to second
    i2cp->slave_addr1 |= 0xF0;
    // the remaining 8 bit of 10-bit address
    i2cp->slave_addr2 = i2cp->id_slave_config->slave_addr & 0x00FF;
    break;
  }

  i2cp->id_slave_config->flags = I2C_FLG_MASTER_RECEIVER;
  i2cp->id_slave_config->errors = 0;

  // Only one byte to be received
  if(i2cp->id_slave_config->rxbytes == 1) {
    i2cp->id_slave_config->flags |= I2C_FLG_1BTR;
  }
  // Only two bytes to be received
  else if(i2cp->id_slave_config->rxbytes == 2) {
    i2cp->id_slave_config->flags |= I2C_FLG_2BTR;
    i2cp->id_i2c->CR1 |= I2C_CR1_POS;            // Acknowledge Position
  }

  i2cp->id_i2c->CR1 |= I2C_CR1_START;            // send start bit

#if !I2C_USE_WAIT
  /* Wait until the START condition is generated on the bus:
   * the START bit is cleared by hardware */
  uint32_t timeout = 0xfffff;
  while((i2cp->id_i2c->CR1 & I2C_CR1_START) && timeout--)
    ;
#endif /* I2C_USE_WAIT */
}


#endif // HAL_USE_I2C