152 lines
4.3 KiB
C
152 lines
4.3 KiB
C
|
/*
|
||
|
|
ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
|
||
|
|
|
||
|
|
Licensed under the Apache License, Version 2.0 (the "License");
|
||
|
|
you may not use this file except in compliance with the License.
|
||
|
|
You may obtain a copy of the License at
|
||
|
|
|
||
|
|
http://www.apache.org/licenses/LICENSE-2.0
|
||
|
|
|
||
|
|
Unless required by applicable law or agreed to in writing, software
|
||
|
|
distributed under the License is distributed on an "AS IS" BASIS,
|
||
|
|
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
||
|
|
See the License for the specific language governing permissions and
|
||
|
|
limitations under the License.
|
||
|
|
*/
|
||
|
|
|
||
|
|
#ifndef _BOARD_H_
|
||
|
|
#define _BOARD_H_
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Setup for the STM32F103C8T6 Module often described as "Arduino"-like
|
||
|
|
* on eBay, typically marked "www.vcc-gnd.com".
|
||
|
|
*/
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Board identifier.
|
||
|
|
*/
|
||
|
|
#define BOARD_MINIMAL_STM32_F103
|
||
|
|
#define BOARD_NAME "STM32F103 Minimal Module"
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Board frequencies.
|
||
|
|
*/
|
||
|
|
#define STM32_LSECLK 32768
|
||
|
|
#define STM32_HSECLK 8000000
|
||
|
|
|
||
|
|
/*
|
||
|
|
* MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
|
||
|
|
*
|
||
|
|
* Only xB (128KB Flash) is defined, but it's identical to the
|
||
|
|
* x8 version (64KB Flash) except for the Flash region size in the
|
||
|
|
* linker script. For x8 parts use xB here and change to the x8 linker
|
||
|
|
* script in the project Makefile.
|
||
|
|
*/
|
||
|
|
#define STM32F103xB
|
||
|
|
|
||
|
|
/*
|
||
|
|
* IO pins assignments
|
||
|
|
*
|
||
|
|
* numbering is sorted by onboard/connectors, as from the schematics in
|
||
|
|
* http://www.vcc-gnd.com/read.php?tid=369
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* on-board */
|
||
|
|
|
||
|
|
#define GPIOC_LED 13
|
||
|
|
|
||
|
|
#define GPIOA_USBDM 11 // pin 8
|
||
|
|
#define GPIOA_USBDP 12 // pin 9
|
||
|
|
|
||
|
|
#define GPIOC_OSC32_IN 14
|
||
|
|
#define GPIOC_OSC32_OUT 15
|
||
|
|
|
||
|
|
/*
|
||
|
|
* I/O ports initial setup, this configuration is established soon after reset
|
||
|
|
* in the initialization code.
|
||
|
|
*
|
||
|
|
* The digits have the following meaning:
|
||
|
|
* 0 - Analog input.
|
||
|
|
* 1 - Push Pull output 10MHz.
|
||
|
|
* 2 - Push Pull output 2MHz.
|
||
|
|
* 3 - Push Pull output 50MHz.
|
||
|
|
* 4 - Digital input.
|
||
|
|
* 5 - Open Drain output 10MHz.
|
||
|
|
* 6 - Open Drain output 2MHz.
|
||
|
|
* 7 - Open Drain output 50MHz.
|
||
|
|
* 8 - Digital input with PullUp or PullDown resistor depending on ODR.
|
||
|
|
* 9 - Alternate Push Pull output 10MHz.
|
||
|
|
* A - Alternate Push Pull output 2MHz.
|
||
|
|
* B - Alternate Push Pull output 50MHz.
|
||
|
|
* C - Reserved.
|
||
|
|
* D - Alternate Open Drain output 10MHz.
|
||
|
|
* E - Alternate Open Drain output 2MHz.
|
||
|
|
* F - Alternate Open Drain output 50MHz.
|
||
|
|
* Please refer to the STM32 Reference Manual for details.
|
||
|
|
*/
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Port A setup.
|
||
|
|
* Everything input with pull-up except:
|
||
|
|
*/
|
||
|
|
#define VAL_GPIOACRL 0x88888888 /* PA7...PA0 */
|
||
|
|
#define VAL_GPIOACRH 0x88888888 /* PA15...PA8 */
|
||
|
|
#define VAL_GPIOAODR 0xFFFFFFFF
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Port B setup.
|
||
|
|
* Everything input with pull-up except:
|
||
|
|
*/
|
||
|
|
#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */
|
||
|
|
#define VAL_GPIOBCRH 0x88888888 /* PB15...PB8 */
|
||
|
|
#define VAL_GPIOBODR 0xFFFFFFFF
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Port C setup.
|
||
|
|
* Everything input with pull-up except:
|
||
|
|
* PC13 - Digital output (LED).
|
||
|
|
*/
|
||
|
|
#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */
|
||
|
|
#define VAL_GPIOCCRH 0x88388888 /* PC15...PC8 */
|
||
|
|
#define VAL_GPIOCODR 0xFFFFFFFF
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Port D setup.
|
||
|
|
* Everything input with pull-up except:
|
||
|
|
* PD0 - Normal input (XTAL).
|
||
|
|
* PD1 - Normal input (XTAL).
|
||
|
|
*/
|
||
|
|
#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */
|
||
|
|
#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */
|
||
|
|
#define VAL_GPIODODR 0xFFFFFFFF
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Port E setup.
|
||
|
|
* Everything input with pull-up except:
|
||
|
|
*/
|
||
|
|
#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */
|
||
|
|
#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */
|
||
|
|
#define VAL_GPIOEODR 0xFFFFFFFF
|
||
|
|
|
||
|
|
/*
|
||
|
|
* USB bus activation macro, required by the USB driver.
|
||
|
|
*/
|
||
|
|
#define usb_lld_connect_bus(usbp) /* always connected */
|
||
|
|
|
||
|
|
/*
|
||
|
|
* USB bus de-activation macro, required by the USB driver.
|
||
|
|
*/
|
||
|
|
#define usb_lld_disconnect_bus(usbp) /* always connected */
|
||
|
|
|
||
|
|
#if !defined(_FROM_ASM_)
|
||
|
|
#ifdef __cplusplus
|
||
|
|
extern "C" {
|
||
|
|
#endif
|
||
|
|
void boardInit(void);
|
||
|
|
#ifdef __cplusplus
|
||
|
|
}
|
||
|
|
#endif
|
||
|
|
#endif /* _FROM_ASM_ */
|
||
|
|
|
||
|
|
#endif /* _BOARD_H_ */
|