tinySA/os/hal/platforms/SPC563Mxx/hal_lld.h

/*
 * Licensed under ST Liberty SW License Agreement V2, (the "License");
 * You may not use this file except in compliance with the License.
 * You may obtain a copy of the License at:
 *
 *        http://www.st.com/software_license_agreement_liberty_v2
 *
 * Unless required by applicable law or agreed to in writing, software 
 * distributed under the License is distributed on an "AS IS" BASIS, 
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

/**
 * @file    SPC563Mxx/hal_lld.h
 * @brief   SPC563Mxx HAL subsystem low level driver header.
 * @pre     This module requires the following macros to be defined in the
 *          @p board.h file:
 *          - SPC5_XOSC_CLK.
 *          .
 *
 * @addtogroup HAL
 * @{
 */

#ifndef _HAL_LLD_H_
#define _HAL_LLD_H_

#include "mpc563m.h"
#include "spc563m_registry.h"

/*===========================================================================*/
/* Driver constants.                                                         */
/*===========================================================================*/

/**
 * @brief   Defines the support for realtime counters in the HAL.
 */
#define HAL_IMPLEMENTS_COUNTERS FALSE

/**
 * @brief   Platform name.
 */
#define PLATFORM_NAME           "SPC563M64"

#define SPC5_RFD_DIV2           0           /**< Divide VCO frequency by 2. */
#define SPC5_RFD_DIV4           1           /**< Divide VCO frequency by 4. */
#define SPC5_RFD_DIV8           2           /**< Divide VCO frequency by 8. */
#define SPC5_RFD_DIV16          3           /**< Divide VCO frequency by 16.*/

/**
 * @name    BIUCR register definitions
 * @{
 */
#define BIUCR_BANK1_TOO         0x01000000  /**< Use settings for bank1 too.*/
#define BIUCR_MASTER7_PREFETCH  0x00800000  /**< Enable master 7 prefetch.  */
#define BIUCR_MASTER6_PREFETCH  0x00400000  /**< Enable master 6 prefetch.  */
#define BIUCR_MASTER5_PREFETCH  0x00200000  /**< Enable master 5 prefetch.  */
#define BIUCR_MASTER4_PREFETCH  0x00100000  /**< Enable master 4 prefetch.  */
#define BIUCR_MASTER3_PREFETCH  0x00080000  /**< Enable master 3 prefetch.  */
#define BIUCR_MASTER2_PREFETCH  0x00040000  /**< Enable master 2 prefetch.  */
#define BIUCR_MASTER1_PREFETCH  0x00020000  /**< Enable master 1 prefetch.  */
#define BIUCR_MASTER0_PREFETCH  0x00010000  /**< Enable master 0 prefetch.  */
#define BIUCR_APC_MASK          0x0000E000  /**< APC field mask.            */
#define BIUCR_APC_0             (0 << 13)   /**< No additional hold cycles. */
#define BIUCR_APC_1             (1 << 13)   /**< 1 additional hold cycle.   */
#define BIUCR_APC_2             (2 << 13)   /**< 2 additional hold cycles.  */
#define BIUCR_APC_3             (3 << 13)   /**< 3 additional hold cycles.  */
#define BIUCR_APC_4             (4 << 13)   /**< 4 additional hold cycles.  */
#define BIUCR_APC_5             (5 << 13)   /**< 5 additional hold cycles.  */
#define BIUCR_APC_6             (6 << 13)   /**< 6 additional hold cycles.  */
#define BIUCR_WWSC_MASK         0x00001800  /**< WWSC field mask.           */
#define BIUCR_WWSC_0            (0 << 11)   /**< No write wait states.      */
#define BIUCR_WWSC_1            (1 << 11)   /**< 1 write wait state.        */
#define BIUCR_WWSC_2            (2 << 11)   /**< 2 write wait states.       */
#define BIUCR_WWSC_3            (3 << 11)   /**< 3 write wait states.       */
#define BIUCR_RWSC_MASK         0x00001800  /**< RWSC field mask.           */
#define BIUCR_RWSC_0            (0 << 8)    /**< No read wait states.       */
#define BIUCR_RWSC_1            (1 << 8)    /**< 1 read wait state.         */
#define BIUCR_RWSC_2            (2 << 8)    /**< 2 read wait states.        */
#define BIUCR_RWSC_3            (3 << 8)    /**< 3 read wait states.        */
#define BIUCR_RWSC_4            (4 << 8)    /**< 4 read wait states.        */
#define BIUCR_RWSC_5            (5 << 8)    /**< 5 read wait states.        */
#define BIUCR_RWSC_6            (6 << 8)    /**< 6 read wait states.        */
#define BIUCR_RWSC_7            (7 << 8)    /**< 7 read wait states.        */
#define BIUCR_DPFEN             0x00000040  /**< Data prefetch enable.      */
#define BIUCR_IPFEN             0x00000010  /**< Instr. prefetch enable.    */
#define BIUCR_PFLIM_MASK        0x00000060  /**< PFLIM field mask.          */
#define BIUCR_PFLIM_NO          (0 << 1)    /**< No prefetching.            */
#define BIUCR_PFLIM_ON_MISS     (1 << 1)    /**< Prefetch on miss.          */
#define BIUCR_PFLIM_ON_HITMISS  (2 << 1)    /**< Prefetch on hit and miss.  */
#define BIUCR_BFEN              0x00000001  /**< Flash buffering enable.    */
/** @} */

/*===========================================================================*/
/* Driver pre-compile time settings.                                         */
/*===========================================================================*/

/**
 * @brief   Disables the clocks initialization in the HAL.
 */
#if !defined(SPC5_NO_INIT) || defined(__DOXYGEN__)
#define SPC5_NO_INIT                         FALSE
#endif

/**
 * @brief   Clock bypass.
 * @note    If set to @p TRUE then the PLL is not started and initialized, the
 *          external clock is used as-is and the other clock-related settings
 *          are ignored.
 */
#if !defined(SPC5_CLK_BYPASS) || defined(__DOXYGEN__)
#define SPC5_CLK_BYPASS                      FALSE
#endif

/**
 * @brief   Disables the overclock checks.
 */
#if !defined(SPC5_ALLOW_OVERCLOCK) || defined(__DOXYGEN__)
#define SPC5_ALLOW_OVERCLOCK                 FALSE
#endif

/**
 * @brief   External clock pre-divider.
 * @note    Must be in range 1...15.
 * @note    The effective divider factor is this value.
 */
#if !defined(SPC5_CLK_PREDIV) || defined(__DOXYGEN__)
#define SPC5_CLK_PREDIV_VALUE                2
#endif

/**
 * @brief   Multiplication factor divider.
 * @note    Must be in range 32...96.
 */
#if !defined(SPC5_CLK_MFD_VALUE) || defined(__DOXYGEN__)
#define SPC5_CLK_MFD_VALUE                  80
#endif

/**
 * @brief   Reduced frequency divider.
 */
#if !defined(SPC5_CLK_RFD) || defined(__DOXYGEN__)
#define SPC5_CLK_RFD                        RFD_DIV4
#endif

/**
 * @brief   Flash buffer and prefetching settings.
 * @note    Please refer to the SPC563M64 reference manual about the meaning
 *          of the following bits, if in doubt DO NOT MODIFY IT.
 * @note    Do not specify the APC, WWSC, RWSC bits in this value because
 *          those are calculated from the system clock and ORed with this
 *          value.
 */
#if !defined(SPC5_FLASH_BIUCR) || defined(__DOXYGEN__)
#define SPC5_FLASH_BIUCR                    (BIUCR_BANK1_TOO |              \
                                             BIUCR_MASTER4_PREFETCH |       \
                                             BIUCR_MASTER0_PREFETCH |       \
                                             BIUCR_DPFEN |                  \
                                             BIUCR_IPFEN |                  \
                                             BIUCR_PFLIM_ON_MISS |          \
                                             BIUCR_BFEN)
#endif

/*===========================================================================*/
/* Derived constants and error checks.                                       */
/*===========================================================================*/

/*
 * Configuration-related checks.
 */
#if !defined(SPC563Mxx_MCUCONF)
#error "Using a wrong mcuconf.h file, SPC563Mxx_MCUCONF not defined"
#endif

#if (SPC5_CLK_PREDIV_VALUE < 1) || (SPC5_CLK_PREDIV_VALUE > 15)
#error "invalid SPC5_CLK_PREDIV_VALUE value specified"
#endif

#if (SPC5_CLK_MFD_VALUE < 32) || (SPC5_CLK_MFD_VALUE > 96)
#error "invalid SPC5_CLK_MFD_VALUE value specified"
#endif

#if (SPC5_CLK_RFD != SPC5_RFD_DIV2) && (SPC5_CLK_RFD != SPC5_RFD_DIV4) &&   \
    (SPC5_CLK_RFD != SPC5_RFD_DIV8) && (SPC5_CLK_RFD != SPC5_RFD_DIV16)
#error "invalid SPC5_CLK_RFD value specified"
#endif

/**
 * @brief   PLL input divider.
 */
#define SPC5_CLK_PREDIV     (SPC5_CLK_PREDIV_VALUE - 1)

/**
 * @brief   PLL multiplier.
 */
#define SPC5_CLK_MFD        (SPC5_CLK_MFD_VALUE)

/**
 * @brief   PLL output clock.
 */
#define SPC5_PLLCLK         ((SPC5_XOSC_CLK / SPC5_CLK_PREDIV_VALUE) *      \
                             SPC5_CLK_MFD_VALUE)

#if (SPC5_PLLCLK < 256000000) || (SPC5_PLLCLK > 512000000)
#error "VCO frequency out of the acceptable range (256...512)"
#endif

/**
 * @brief   PLL output clock.
 */
#if !SPC5_CLK_BYPASS || defined(__DOXYGEN__)
#define SPC5_SYSCLK         (SPC5_PLLCLK / (1 << (SPC5_CLK_RFD + 1)))
#else
#define SPC5_SYSCLK         SPC5_XOSC_CLK
#endif

#if (SPC5_SYSCLK > 80000000) && !SPC5_ALLOW_OVERCLOCK
#error "System clock above maximum rated frequency (80MHz)"
#endif

/**
 * @brief   Flash wait states are a function of the system clock.
 */
#if (SPC5_SYSCLK <= 30000000) || defined(__DOXYGEN__)
#define SPC5_FLASH_WS       (BIUCR_APC_0 | BIUCR_RWSC_0 | BIUCR_WWSC_1)
#elif SPC5_SYSCLK <= 60000000
#define SPC5_FLASH_WS       (BIUCR_APC_1 | BIUCR_RWSC_1 | BIUCR_WWSC_1)
#else
#define SPC5_FLASH_WS       (BIUCR_APC_2 | BIUCR_RWSC_2 | BIUCR_WWSC_1)
#endif

/*===========================================================================*/
/* Driver data structures and types.                                         */
/*===========================================================================*/

/*===========================================================================*/
/* Driver macros.                                                            */
/*===========================================================================*/

/*===========================================================================*/
/* External declarations.                                                    */
/*===========================================================================*/

#include "spc5_edma.h"

#ifdef __cplusplus
extern "C" {
#endif
  void hal_lld_init(void);
  void spc_clock_init(void);
#ifdef __cplusplus
}
#endif

#endif /* _HAL_LLD_H_ */

/** @} */