Due to nets being optimized at IP-level during the no-OOC synthesis flow,
constraints related to req_clk (request clock) were not being applied,
causing the design to not meet timing.
The fix considers the synchronous modes, appending the possible resulting
req_clk's names after the synthesis flow.
Due to grounded signals in the DMA_TYPE_SRC != DMA_TYPE_STREAM_AXI config.,
sync_rewind is removed during synthesis, even so, constraints were
trying to be applied to those nets.
To resolve this, sync_rewind block was moved to inside the generate.
Vivado seems to properly suppress "Empty list" warnings when the circuit does not exist because of a generate rule.
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Signed-off-by: Ionut Podgoreanu <ionut.podgoreanu@analog.com>
New improvements for the ADI DMAC IP:
1)The capability to manually overwrite the DMA_AXI_ADDR_WIDTH(from GUI or from tcl)
2)DMA_AXI_ADDR_WIDTH attribute is now visible in the Vivado GUI:
-"Auto mode": Automatically calculated by the core tcl files based on the existing attached address segments.
-"Manual mode": Specify the desired dma_width between 32-64 bits.
3)Added two new debug registers that return higher part of the current source/destination address.
Signed-off-by: Filip Gherman <Filip.Gherman@analog.com>
* Added header license for the files that didn't have
* Modified parentheses
* Removed extra spaces at the end of lines
* Fixed parameters list to be each parameter on its line
* Deleted lines after endmodule and consecutive empty lines
* Fixed indentation
Signed-off-by: Iulia Moldovan <iulia.moldovan@analog.com>
On architectures with ports that support cache coherency, the AWCACHE
signal must be set to indicate that transactions are cached. This patch
adds a parameter allowing AWCACHE to be set on an AXI4 destination port.
On large projects with multiple channels the databus on the FIFO/AXI
stream interface can get wider that 1024 bits.
This commit allows a wider range for all the interfaces,
in case for the memory mapped interfaces where the range is 32-1024 the
user selects a bus width out of range that will be handled by the IPI.
Create a common 'run_tb.sh' script to be called by every testbench.
Unify file and testbenches names.
Fix util_pack/cpack_tb.
Add parameters '-batch' and '-gui' for modelsim and xsim simulators (default is gui)
Add ascript for that generates output in xml format (used by CI tools).
Adds information on:
- Log 2 of interface data widths in bits
- Interface type (0 - Axi MemoryMap, 1 - AXI Stream, 2 - FIFO ) .
Lets the driver discover interface widths and interface type settings,
this will deprecate the corresponding device tree properties.
This is useful in case of parametrized projects where the width of
the datapath is changing. This change will allow the use of a generic
device tree node.
Updated version to 4.3.a
In some cases, the Vivado version can contain other characters than just
numbers. One such example is after applying the patch of AR# 71948,
which makes `version -short` return something like `2018.3_AR71948`.
This patch changes the version check to ignore anything after the first
two components of the version.
Let the measured transfer length to be cleared at the end of each
transfer, other case in cyclic mode the counter will overflow and will
not present any useful information.
Once xfer_request is set the DMA must accept samples in the same clock
cycle if the fifo_wr_en signal is asserted.
If the req_valid asserts faster than the ID gets synchronized over the
the xfer request asserts without being ready to accept data.
This can lead to overflow assertion when using a FIFO like interface.
This patch addresses the following issue:
In case of transfers with multiple segments, if TLAST asserts on the last
beat of a non-last segment while more descriptors are queued up,
the completions for the queued segments may be missed causing timeout in
processes that wait for transfer completions.
This patch addresses the following issue:
In 2D mode when consecutive partial transfers occur, and the latter is
very short, will interfere with the completion mechanism of the first
transfer leading to uncompleted segments and unreported partial
transfers.
The tb_base.v verilog files does not contain a full module definition,
just some plain test code. In general the files is sourced inside the
test bench main module. As is, defining a timescale in these files will
generate an error, because timescale directive can not be inside a
module.
Delete all the timescale directive from these files.
The interrupt controller from Microblaze based projects requires that
all its inputs have attributes which define the sensitivity of the
interrupt line. Other case it defaults to EDGE_RISING which is not the
case for DMAC, leading to incorrect interrupt reporting and handling in
case of such projects.
Iulia Moldovan
Jorge Marques
Filip Gherman
Iacob_Liviu
Mathias Tausen
Ionut Podgoreanu
Nick Pillitteri
Laszlo Nagy
Adrian Costina
alin724
Alin-Tudor Sferle
stefan.raus
Aaron Holtzman
Istvan Csomortani
Arpadi