c5d216bba9
adrv9001/zcu102: Enable independent TX mode in CMOS
...
For CMOS case, lane rates are so low that reference clock of the source
synchronous interface can be routed on non-clock routes. The delays on
the clock line are adjusted by the digital interface tuning controlled
through software.
Lock down clock buffers on Rx and Tx interfaces, this avoids suboptimal
placement which causes large skew between clocks at the serdes pins.
2021-10-27 14:40:08 +03:00
03682f6193
projects/adrv9001/zcu102/lvds_constr.xdc: Fix timing constraints
...
1. Reduce max allowed skew between source synchronous clocks that can
occur due PCB differences. 250ps represents a difference more than an
inch.
2. In order to reduce skew between source synchronous clock and the
divided clock instruct the tool to use a common clock root for them.
2021-10-27 14:40:08 +03:00
51b643b978
Makefile: Fix misc makefiles from projects and library
2021-10-05 14:24:48 +03:00
591a23156b
Makefiles: Update header with the appropriate license
2021-09-16 16:50:53 +03:00
16a93a804b
adrv9001[intel]: Add second pair of DMAs
...
fix observations for PR
2021-09-01 15:04:14 +03:00
63ac142874
adrv9001:a10soc:system_qsys.tcl: set clock polarity to 0
...
For fixing "Failed to reset the device and set SPI Config"
error, both clockPolarity and clockPhase should be disabled
or both enabled. By default both are unset.
Signed-off-by: Stefan Raus <stefan.raus@analog.com>
2021-06-16 11:42:50 +03:00
d9bc014c98
adrv9001/zcu102: Enable independent Tx from Rx in CMOS mode
2021-05-26 15:44:45 +03:00
568bef4a38
adrv9001/a10soc: Initial version
...
This project supports CMOS mode only.
2021-05-26 15:44:45 +03:00
dcec4fe1b7
adrv9001/zc706: Fix spaces
2021-03-10 10:35:52 +02:00
dc186645d8
adrv9001/zc706: Fix comments HPC to LPC
2021-03-10 10:35:52 +02:00
677c154134
adrv9001/zcu102/cmos: Loosen up clock skew constraints to match LVDS settings
...
Set the same inter clock skew characteristics as used in LVDS mode. The
physical lanes/routes are common on both modes.
2021-03-04 11:13:10 +02:00
0dd3173547
adrv9001/zc706: Initial commit
...
The project supports CMOS interface only.
VADJ on the ZC706 must be programmed to 1.8V
Instructions can be found here:
https://www.xilinx.com/Attachment/ZC706_Power_Controllers_Reprogramming_Steps.pdf
https://forums.xilinx.com/t5/Xilinx-Evaluation-Boards/ZC706-Doesn-t-work-with-VADJ-at-1-8v/td-p/430086
2021-03-03 09:03:03 +02:00
dd4c8d6807
adrv9001/zcu102: Add debug header
2021-01-26 15:22:41 +02:00
728904af09
adrv9001/zcu102: Run postRoutePhysOpt to close Rx1 to Rx2 path timing
2021-01-26 15:22:41 +02:00
bae7e48c50
adrv9001/common: Run DMAs @ 100MHz
2021-01-26 15:22:41 +02:00
bb44e5399f
adrv9001/zed: Connect TDD sync to PMOD JA1
2021-01-20 13:00:01 +02:00
3918d43cd1
adrv9001/zcu102: Add TDD sync to PMOD0 J55.1
2021-01-20 13:00:01 +02:00
fe9f72db9c
adrv9001/common: Export TDD mode signal
2021-01-20 13:00:01 +02:00
18b2a8b0a7
adrv9001/zed: Add TDD support
2021-01-20 13:00:01 +02:00
0c2745361b
adrv9001/zcu102: Add TDD support
2021-01-20 13:00:01 +02:00
6f2f2b8626
makefile: Regenerate make files
2021-01-20 01:02:56 +02:00
acbbd4636a
sysid: Upgrade framework, header/ip are now at 2/1.1.a
...
Unify tcl scripts; rename adi_pd_intel.tcl to adi_pd.tcl
add git branch to internal use area; update log prints;
update xilixn projects; fix cn0506 sysid script;
2021-01-20 01:02:56 +02:00
9093a8c428
library: Move ad_iobuf to the common library, as it's not Xilinx specific
...
Updated all system_project and Makefiles
2020-11-02 16:13:35 +02:00
37254358dd
makefile: Regenerate make files
2020-10-20 12:51:10 +03:00
d8ab27b2af
sysid: Remove cstring init string
2020-09-30 19:12:24 +03:00
24090fafd8
adrv9001/zcu102: Loopback VADJ error to the FMC board
2020-08-31 14:14:03 +03:00
d14376547f
adrv9001/zed: Refactor VADJ test in VADJ error
...
The ADRV9002 uses in the digital interface 1.8V, however the Zed VADJ is
selectable by a jumper can go up to 3.3V . Voltage levels higher than 1.8V
are detected by the EVAL-ADRV9002 board, asserting the VADJ_ERR pin.
If VADJ error is set high keep all drivers in high-z state and signalize
it to the software layer through a gpio line.
2020-08-31 14:14:03 +03:00
72f916fcf5
adrv9001/zcu102: Update interface signal names based on direction
...
Let the names of signals from source synchronous interface match the
direction of the signals.
2020-08-28 13:23:00 +03:00
a212ad6e58
adrv9001/zed: Update interface signal names based on direction
...
Let the names of signals from source synchronous interface match the
direction of the signals.
2020-08-28 13:23:00 +03:00
118e1f9e8b
adrv9001/zed: Initial support for Zed
...
CMOS only support for ADRV9001 on ZedBoard
2020-08-24 17:49:12 +03:00
b27f3ac18f
adrv9001:zcu102: Initial version
...
Generic project that supports CMOS or LVDS interface for the ADRV9001 transceiver.
2020-08-24 17:49:12 +03:00
Laszlo Nagy
Adrian Costina
LIacob106
stefan.raus
Sergiu Arpadi
Istvan Csomortani