63ac142874
adrv9001:a10soc:system_qsys.tcl: set clock polarity to 0
...
For fixing "Failed to reset the device and set SPI Config"
error, both clockPolarity and clockPhase should be disabled
or both enabled. By default both are unset.
Signed-off-by: Stefan Raus <stefan.raus@analog.com>
2021-06-16 11:42:50 +03:00
d9bc014c98
adrv9001/zcu102: Enable independent Tx from Rx in CMOS mode
2021-05-26 15:44:45 +03:00
568bef4a38
adrv9001/a10soc: Initial version
...
This project supports CMOS mode only.
2021-05-26 15:44:45 +03:00
dcec4fe1b7
adrv9001/zc706: Fix spaces
2021-03-10 10:35:52 +02:00
dc186645d8
adrv9001/zc706: Fix comments HPC to LPC
2021-03-10 10:35:52 +02:00
677c154134
adrv9001/zcu102/cmos: Loosen up clock skew constraints to match LVDS settings
...
Set the same inter clock skew characteristics as used in LVDS mode. The
physical lanes/routes are common on both modes.
2021-03-04 11:13:10 +02:00
0dd3173547
adrv9001/zc706: Initial commit
...
The project supports CMOS interface only.
VADJ on the ZC706 must be programmed to 1.8V
Instructions can be found here:
https://www.xilinx.com/Attachment/ZC706_Power_Controllers_Reprogramming_Steps.pdf
https://forums.xilinx.com/t5/Xilinx-Evaluation-Boards/ZC706-Doesn-t-work-with-VADJ-at-1-8v/td-p/430086
2021-03-03 09:03:03 +02:00
dd4c8d6807
adrv9001/zcu102: Add debug header
2021-01-26 15:22:41 +02:00
728904af09
adrv9001/zcu102: Run postRoutePhysOpt to close Rx1 to Rx2 path timing
2021-01-26 15:22:41 +02:00
bae7e48c50
adrv9001/common: Run DMAs @ 100MHz
2021-01-26 15:22:41 +02:00
bb44e5399f
adrv9001/zed: Connect TDD sync to PMOD JA1
2021-01-20 13:00:01 +02:00
3918d43cd1
adrv9001/zcu102: Add TDD sync to PMOD0 J55.1
2021-01-20 13:00:01 +02:00
fe9f72db9c
adrv9001/common: Export TDD mode signal
2021-01-20 13:00:01 +02:00
18b2a8b0a7
adrv9001/zed: Add TDD support
2021-01-20 13:00:01 +02:00
0c2745361b
adrv9001/zcu102: Add TDD support
2021-01-20 13:00:01 +02:00
6f2f2b8626
makefile: Regenerate make files
2021-01-20 01:02:56 +02:00
acbbd4636a
sysid: Upgrade framework, header/ip are now at 2/1.1.a
...
Unify tcl scripts; rename adi_pd_intel.tcl to adi_pd.tcl
add git branch to internal use area; update log prints;
update xilixn projects; fix cn0506 sysid script;
2021-01-20 01:02:56 +02:00
9093a8c428
library: Move ad_iobuf to the common library, as it's not Xilinx specific
...
Updated all system_project and Makefiles
2020-11-02 16:13:35 +02:00
37254358dd
makefile: Regenerate make files
2020-10-20 12:51:10 +03:00
d8ab27b2af
sysid: Remove cstring init string
2020-09-30 19:12:24 +03:00
24090fafd8
adrv9001/zcu102: Loopback VADJ error to the FMC board
2020-08-31 14:14:03 +03:00
d14376547f
adrv9001/zed: Refactor VADJ test in VADJ error
...
The ADRV9002 uses in the digital interface 1.8V, however the Zed VADJ is
selectable by a jumper can go up to 3.3V . Voltage levels higher than 1.8V
are detected by the EVAL-ADRV9002 board, asserting the VADJ_ERR pin.
If VADJ error is set high keep all drivers in high-z state and signalize
it to the software layer through a gpio line.
2020-08-31 14:14:03 +03:00
72f916fcf5
adrv9001/zcu102: Update interface signal names based on direction
...
Let the names of signals from source synchronous interface match the
direction of the signals.
2020-08-28 13:23:00 +03:00
a212ad6e58
adrv9001/zed: Update interface signal names based on direction
...
Let the names of signals from source synchronous interface match the
direction of the signals.
2020-08-28 13:23:00 +03:00
118e1f9e8b
adrv9001/zed: Initial support for Zed
...
CMOS only support for ADRV9001 on ZedBoard
2020-08-24 17:49:12 +03:00
b27f3ac18f
adrv9001:zcu102: Initial version
...
Generic project that supports CMOS or LVDS interface for the ADRV9001 transceiver.
2020-08-24 17:49:12 +03:00
stefan.raus
Laszlo Nagy
Sergiu Arpadi
Adrian Costina
Istvan Csomortani