This feature will allow the user to hold(indefinitely) the last sample, from an
ongoing DMA transfer, simple or cyclic(stooped by user or trigger).
This commit also adds as functionality option:
-synchronized stop between the two channels(DMAs)
-stop by trigger
Optimize the oversampling mechanism.
The behavior of the axi_dac_interpolate was changing if a debug module was
added to the core.
The current code has a better utilization and reliability.
When using an oversampling of 2 for axi_dac_interpolate the rate was
the same as with oversampling by 1(bypassing).
This commit removes the bypass for the ratio of 2.
The previous mechanism was "probing" the DMAs for valid data. Better said,
each interpolation channel enabled it's DMA until a valid data was received,
then it disabled the DMA read and waited for the adjacent channel(DMA) to
receive a valid data. Only when for both channels had valid data on the
DMAs interfaces was the transmission started. This added an undesired and
redundant complexity to the interpolation channels. Furthermore, for continuous
transmission, using the above mechanism lead to a fixed phase(sample)
shift between the two channels at each start.
By using the streaming mechanism the interface is simplified and the
above problems are solved.
The previous channel sync mechanism was simply holding the transmission by
pulling down the dma_rd_en of the two DMAs for each channel(set reg 0x50). After a
period of time (that will take the two DMAs to have the data ready to move)
the dma_rd_en was set for both channels, resulting in a synchronized start.
This mechanism is valid when the two channels are streaming the same
type of data (constant, waveform, buffer or math) at close frequencies.
Streaming 10MHz on a channel and 100KHz on the second one will result
in different interpolation factors being used for the two channels.
The interpolation counter runs only when the dma_transfer_suspended(reg 0x50)
is cleared. Because of this, different delays are added by the interpolation
counter one DMA with continuous dma_rd_en will have data earlier than the
one with dma_rd_en controlled by the interpolation counter. Furthermore,
because the interpolation counter value is not reset at each
dma_transfer_suspended, the phase shift between the 2 channels will
differ at each start of transmission.
To make the transfer start synced immune to the above irregularities a
sync_transfer_start register was added (bit 1 of the 0x50 reg).
When this bit is set and the bit 0(dma_transfer_suspended) is toggled,
the interpolation counters are reset. Each channel enables it's DMA until
valid data is received, then it waits for the adjacent channel to get valid data.
This mechanism will be simplified in a future update by using a streaming
interface between the axi_dac_interpolate and the DMAs that does not require
the probing of the DMA.
Currently the individual IP core dependencies are tracked inside the
library Makefile for Xilinx IPs and the project Makefiles only reference
the IP cores.
For Altera on the other hand the individual dependencies are tracked inside
the project Makefile. This leads to a lot of duplicated lists and also
means that the project Makefiles need to be regenerated when one of the IP
cores changes their files.
Change the Altera projects to a similar scheme than the Xilinx projects.
The projects themselves only reference the library as a whole as their
dependency while the library Makefile references the individual source
dependencies.
Since on Altera there is no target that has to be generated create a dummy
target called ".timestamp_altera" who's only purpose is to have a timestamp
that is greater or equal to the timestamp of all of the IP core files. This
means the project Makefile can have a dependency on this file and make sure
that the project will be rebuild if any of the files in the library
changes.
This patch contains quite a bit of churn, but hopefully it reduces the
amount of churn in the future when modifying Altera IP cores.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
This reduces the amount of boilerplate code that is present in these
Makefiles by a lot.
It also makes it possible to update the Makefile rules in future without
having to re-generate all the Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The up_xfer_cntrl and up_xfer_status modules have its own constraints files
in library/xilinx/common. Each IP which has an instance of these
modules, have to use these constraints files.
The following IPs were modified:
- axi_adc_decimate
- axi_adc_trigger
- axi_dac_interpolate
- axi_logic_analyzer
The CIC filter introduces different amplifications depending on the
interpolation ratio. By adding a multiplier in the interpolation chain
the amplification can be compensated
All the hdl (verilog and vhdl) source files were updated. If a file did not
have any license, it was added into it. Files, which were generated by
a tool (like Matlab) or were took over from other source (like opencores.org),
were unchanged.
New license looks as follows:
Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
Each core or library found in this collection may have its own licensing terms.
The user should keep this in in mind while exploring these cores.
Redistribution and use in source and binary forms,
with or without modification of this file, are permitted under the terms of either
(at the option of the user):
1. The GNU General Public License version 2 as published by the
Free Software Foundation, which can be found in the top level directory, or at:
https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
OR
2. An ADI specific BSD license as noted in the top level directory, or on-line at:
https://github.com/analogdevicesinc/hdl/blob/dev/LICENSE
The axi_dac_interpolate does not use the full width of the AXI interface
address. It only responds to register access in the first 32 registers.
Reduce the size of the AXI address to 7 bit accordingly. This allows the
scripts to correctly infer the internal register map size which will cause
the interconnect to filter out access to these unused register.
This slightly reduces utilization by getting rid of some pipeline
registers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The output data mux is used to bypass the filter when it is not used. Which
setting is used for the mux depends on the 3-bit filter_mask signal.
Registering the control logic into a single bit signal reduces the amount
of routing resources required. Since changing the filter_mask settings is
asynchronous to the processing anyway the extra clock cycle delay
introduced by this change does not affect behaviour.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Move the processing pipeline of the axi_adc_decimate core to its own
sub-module. This makes it easier to simulate the processing independent of
the register map.
Also since the filter is two instances of the same logic, one for each
channel, let the new sub-module model one channel and instantiate it twice.
This allows to change the implementation without having to change the same
code twice.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Xilinx recommends that all synchronizer flip-flops have
their ASYNC_REG property set to true in order to preserve the
synchronizer cells through any logic optimization during synthesis
and implementation.
LIacob106
Adrian Costina
AndreiGrozav
Istvan Csomortani
Arpadi
Lars-Peter Clausen
Rejeesh Kutty