59313f3c90
daq1: ADC DMA must be in none-cyclic mode
2016-02-24 14:37:19 +02:00
c0a559a9b1
daq1: Fix some typos in the SPI wrapper
2016-02-24 14:31:56 +02:00
8ccd8d87bb
daq2: A10GX, increase analog/digital reset durations
...
- reset the xcvr_rst_cntrl only from the axi_jesd_xcvr
- checked separate RX/TX reset per channel
2016-02-23 11:41:38 +02:00
89f7aadfb1
fmcjesdadc1: A5GT, connected xcvr_rxt_cntrl reset input to the axi_jesd_xcvr reset output
...
This will allow for the transceivers to be reset by the axi_jesd_xcvr core
2016-02-23 11:31:07 +02:00
4fb6589b2d
pzsdr/ccfmc: add fan controls
2016-02-19 16:40:54 -05:00
377461e0d4
Merge branch 'hdl_2015_r2' into dev
2016-02-19 14:15:27 +02:00
0f37dd6424
fmcjesdadc1: Fixed project
...
- changed system_project.tcl so that all base designs to be included
- changed DMA properties to take into consideration the new parameter names
- changed reset bridges to asynchronous
- increased maximum burst size of the DMA bridge
- changed the data_width of the memory bus to 256, as with 512 timing violations may occur
- changed base addresses for the base system to be the same as in the previous release
2016-02-19 14:09:57 +02:00
ce760eb691
fmcadc2- add adf4355 access
2016-02-18 16:17:33 -05:00
a8e9d72273
adc/dac - prefix parameters
2016-02-17 14:16:04 -05:00
d94f157454
arradio: Changed ADC/DAC DMA address length to 24 bit
2016-02-16 15:27:51 +02:00
43e03ca6f7
arradio: Updated project
...
- made the reset bridges asynchronous
- connected the arradio gpio to the CPU interconnect
2016-02-16 14:50:23 +02:00
5518c47ca4
daq1_cpld: Set Input and tristate I/O termination mode to FLOAT
2016-02-15 19:27:59 +02:00
051ac307e6
daq1_cpld: Do not forward the first eight clock cycles of fmc_spi_sclk to sclk
2016-02-15 19:26:58 +02:00
9370246cfa
daq1: Fix bugs on CPLD design
...
Fix the CSN forwarding.
2016-02-12 16:59:09 +02:00
5ed2c0b599
daq1: Update CPLD constraints file
2016-02-12 16:54:36 +02:00
aa2ff0223a
daq1: Update CPLD design
...
+ SPI counter counts on negative edge of the SPI_CLK
+ Shift register for read, shifting MSB first
+ Fix write access logic
+ Update the internal register addresses
2016-02-12 14:45:18 +02:00
e1c5d6a8f7
axi_ad9684: Fix constraint file
2016-02-12 14:38:59 +02:00
c32d7147d5
daq1 : There is a single CSN from master
2016-02-12 14:38:32 +02:00
9675df15c6
daq1_zc706: Update constraints file
2016-02-12 14:37:02 +02:00
a747fad540
axi_ad9361: tx_valid must be controlled by the TDD controller
2016-02-12 14:33:34 +02:00
e381d5170c
util_tdd_sync: Update the synchronization interface
...
Simplify the synchronization interface, there is one signal line between the synchronization module and transceiver core.
2016-02-12 14:27:37 +02:00
1c3795ad02
Update .gitattributes
...
Add xise file extension to .gitattributes
2016-02-12 14:27:35 +02:00
61f9f72a75
fmcjesdadc1: Updated VC707 project for maximum throughput from DMA to DDR
...
- Increased the DMAs internal FIFO
2016-02-09 12:30:56 +02:00
c431adb793
fmcjesdadc1: Updated KC705 project for maximum throughput from DMA to DDR
...
- Increased the DMA internal FIFO
2016-02-09 12:00:27 +02:00
ad9ecbbbb6
daq2: Updated a10gx project to quartus 15.1.1
2016-02-05 17:43:05 +02:00
0d67af370f
util_upack: Fixed problem when dac valid isn't continuous from the DAC
...
In cases when the dac_valid_ from the DAC is not continuous, in some situations
there were two dac_valid pulses sent to the DMA.
2016-02-04 13:03:46 +02:00
bb62f6d225
pzsdr1- updates
2016-02-02 12:34:09 -05:00
41b6ebeeaf
pzsdr1- updates
2016-02-02 12:33:55 -05:00
b147e9c94a
pzsdr1- updates
2016-02-02 12:33:01 -05:00
170295161f
pzsdr1- xdc
2016-01-26 11:19:00 -05:00
bcac3eef4d
pzsdr1- initial commit
2016-01-25 16:07:33 -05:00
44a382fc69
pzsdr1-added
2016-01-25 15:33:34 -05:00
e22d5d5c18
daq2: Fix clock constraints for KC705 and VC707
2016-01-22 19:09:57 +02:00
59fbd99fdb
fmcjesdadc1: Added clock constraint for the ADC path
2016-01-22 15:46:20 +02:00
dca39c26f9
ad6676evb: Added clock constraint for the ADC path
2016-01-22 15:45:16 +02:00
9cd0378003
fmcadc2: Added clock constraint for the ADC path
2016-01-22 15:44:04 +02:00
aa77af6bdf
daq1_cpld: Add ISE project file
...
This file, along with the project source files, is sufficient to open and implement in ISE Project Navigator.
2016-01-21 18:05:59 +02:00
4cc69c0cac
axi_ad9684: Add Makefile
2016-01-19 18:32:11 +02:00
c865dbf353
axi_ad9680: Fix channel instantiation
2016-01-19 12:49:45 +02:00
df3eefdca1
axi_ad9434: Update constraint file
2016-01-19 12:43:05 +02:00
8c69c9d2ce
daq1_zc706 : Update the project
...
+ Add AD9684 to the block design
+ Update the IO definitions
+ Update the CPLD design
+ Add 3wire SPI logic
2016-01-19 11:20:35 +02:00
d1e638349b
ad_serdes_clk : The reference clock selection line should by tied to 1
...
Just the CLKIN1 is used in the MMCM.
2016-01-19 11:18:00 +02:00
c6cfd1a2b6
axi_ad9684: Initial check in
2016-01-19 11:13:45 +02:00
ab99c4456a
ad9434_fmc: Delete unnecessary set_property call
...
HPx interface is activated by the ad_mem_hpx_interconnect process
2016-01-14 15:41:23 +02:00
c094ab8b52
cn0363: Add support for the MicroZed
...
Add support for connecting the CN0363 to the MicroZed. This works in
combination with the MicroZed Arduino carrier board. The CN0363 needs to be
connected to the PLPMOD header.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2016-01-13 20:32:26 +01:00
514eb68876
cn0363: Factor out common parts
...
Factor out the common parts of the cn0363 design so we can use it to add
support for other carriers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2016-01-13 20:32:26 +01:00
d2b26720e6
common: microzed: Add clock, reset and interrupt support
...
In order for the base project to be usable by other projects it needs to
create the clock, reset and interrupt signals that are expected to exist.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2016-01-13 20:32:26 +01:00
51d20b1a61
adi_project.tcl: Add MicroZed support
...
Handle the projects for the MicroZed and set up the FPGA part accordingly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2016-01-13 20:32:26 +01:00
426490c394
common: Rename uzed to microzed
...
Everybody calls the MicroZed microzed in their projects. Don't deviate from
that to avoid potential confusion.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
2016-01-13 20:18:57 +01:00
4f2b999999
axi_ad9680: Q_OR_I_N is not used in this channel
2016-01-13 16:26:22 +02:00
Istvan Csomortani
Adrian Costina
Rejeesh Kutty
István Csomortáni
Lars-Peter Clausen