ADRV9001 interfacing IP supports the following modes on Xilinx devices:
A B C D E F G H
CSSI__1-lane 1 32 80 80 2.5 SDR 8
CSSI__1-lane 1 32 160 80 5 DDR 4
CSSI__4-lane 4 8 80 80 10 SDR 2
CSSI__4-lane 4 8 160 80 20 DDR 1
LSSI__1-lane 1 32 983.04 491.52 30.72 DDR 4
LSSI__2-lane 2 16 983.04 491.52 61.44 DDR 2
Columns description:
A - SSI Modes
B - Data Lanes Per Channel
C - Serialization factor Per data lane
D - Max data lane rate(MHz)
E - Max Clock rate (MHz)
F - Max Sample Rate for I/Q (MHz)
G - Data Type
H - DDS Rate
CSSI - CMOS Source Synchronous Interface
LSSI - LVDS Source Synchronous Interface
Intel devices supports only CSSI modes.
De-assert dac_rst together with an updated control set.
This allows writing the control registers before releasing the reset.
This is important at start-up when stable set of controls is required.
De-assert adc_rst together with an updated control set.
This allows writing the control registers before releasing the reset.
This is important at start-up when stable set of controls is required.
Allow monitoring of non-PN patterns which have zeros in it.
e.g. nible-ramp, full range ramp.
Singular zeros got ignored if not out of sync, while OOS_THRESHOLD
consecutive zeros or non-matching data asserts the out of sync line.
Fix the *_ip.tcl scripts for axi_spi_engine and spi_engine_offload
module.
In case of a bool parameters the value_format and value properties must
be set for both user and hdl paramters. If not, in the generated verilog
code the tool will use "true" or "false" strings, instead of 0 or 1.
The input data path has a delay section that compensates for the ADC path delay.
By using a Dynamic Shift Registers coding style we can improve/change the
resource utilization on m2k:
Before After Resources
LUT 10097 10048 48 (0.28%)
LUTRAM 516 540 -24 (-0.4%)
FF 15285 14803 482 (1.37%)
The number of delay taps in the LA data path can be controlled manually, from
the regmap or automatically, according to the axi_adc_decimate's rate.
Moreover, because the rate is configure by software, and the time of
initialization, is different for the ADC path and LA path. There is an
uncertainty of plus/minus one sample between the two. Because ADC and LA
paths share the same clock we can easily synchronize the two paths. We
can't use reset, because the rate generation mechanism is different
between the two. So the ADC path is used as master valid generator and we
can use it to drive the LA path.
The synchronization is done by setting the rate source bit. This
mechanism can only be used if the desired rate for both path is equal,
including oversampling fom ADC decimation.
Adds information on:
- Log 2 of interface data widths in bits
- Interface type (0 - Axi MemoryMap, 1 - AXI Stream, 2 - FIFO ) .
Lets the driver discover interface widths and interface type settings,
this will deprecate the corresponding device tree properties.
This is useful in case of parametrized projects where the width of
the datapath is changing. This change will allow the use of a generic
device tree node.
Updated version to 4.3.a
Optimize the oversampling mechanism.
The behavior of the axi_dac_interpolate was changing if a debug module was
added to the core.
The current code has a better utilization and reliability.
When using an oversampling of 2 for axi_dac_interpolate the rate was
the same as with oversampling by 1(bypassing).
This commit removes the bypass for the ratio of 2.
For projects where the clock ratio between the sampling clock and core clock
is higher than 2, the ad_dds generates a number of samples equal with
the clock ratio. There is a phase offset between the samples, proportional
with the requested DDS frequency.
In scenarios where the DDS out frequency is closer to the upper
limit(Nyquist) and/or the clock ratio is also greater than 2 and the
dac_data_sync reminds low for an extended period of time, the DAC will
receive at each core clock period, a number of samples equal with the
clock ratio and with an amplitude influenced by the DDS out frequency.
In most cases similar with a sawtooth signal.
With this commit we ensures that samples received by the DAC are 0 for
the period where dac_data_sync signal is high. Only when the signal
transitions to low, the phase accumulator is initialized and the phase
information is passed to the phase to amplitude converter.
Another issue can appear when the sync signal is too short; less then
CLK_RATIO * clock cycles. Because the phase accumulator will not
synchronize at all stages, the final result will be a random combination of
sine-waves. Added a minimum sync pulse after the dac_data_sync is set
low.
When frame alignment error monitoring is enabled and error threshold is met
at least for one lane, generate an interrupt so software can reset the link and
do further bring-up steps.
Add support for RX frame alignment character checking when scrambling is enabled and
for link reset on misalignment.
Add support for xcelium simulator to jesd204/tb
The Pattern generator is part of the axi_logic_analyzer core.
The trigger signal can be internal (Oscilloscope or Logic Analyzer) or
external(TI or TO pins).
The sdo_enabled and sdi_enabled control lines are generated from the
current state of the CMD bus.
In case of a delayed SDI latching the sdi_enabled can be deasserted at
the moment of the last valid bit, losing the generation of the sdi_data_valid
signal, which eventually cause a data loss, or even deadlock on software driver.
To make the logic mode robust, latch the value of the CMD[9:8] at every
transfer command. Doing so the sdo_enabled and sdi_enabled control lines will
store the last active transfer command state and they will be
independent of the current state of the CMD bus. This way we can add
longer time delay to the SDI latching if it's necessary.
Having the same name for dac and adc TPLs creates conflict in the
address segment naming having random names associated to the segments.
This causes difficulties during scripting of the project in test bench
mode.
The value of the HDL parameter NUM_OF_SDI can be read out from the
register at address 0x0C. The same register contains the value of the
DATA_WIDTH.
The register has the following bit layout:
[15: 0] DATA_WIDTH
[23:16] NUM_OF_SDI
[31:24] 8'b0
Forward the offload's sync_id to the register map, by defining an
additional AXI stream interface between the offload and axi_spi_engine.
The last sync_id of the offload module can read out from the
register 0x00C4. It also can generate and interrupt if the irq mask is
configured accordingly.
There is a major compatibility issue between 2019.1 and 2019.2.
The file system_top.hdf got a different file extention. This will
cause a compilation failer in the end of the build. To save time
and fail earlier, upgrade the version mismatch message to ERROR.
If user still wants to build a branch with different tool version
the variable ADI_IGNORE_VERSION_CHECK should be set to 1.
The external synchronization signal should be synchronous with the
dac clock. Synchronization will be done on the rising edge of the signal.
The control bit is self clearing. Status bit shows that the synchronization
is armed but the synchronization signal has not yet been received
Added EXT_SYNC parameter to be able to keep the dac_sync original
behavior
The external synchronization signal should be synchronous with the
adc clock. Synchronization will be done on the rising edge of the signal.
The control bit is self clearing. Status bit shows that the synchronization
is armed but the synchronization signal has not yet been received. While
the synchronization mechanism is armed, the adc_rst output signal is set
The current format should allow for the SYSREF signal to be used as
synchronous capture start, but will need to be disabled before the
synchronization mechanism is armed
The commit 9ab88f1200 introduced a new
feature for the execution module, which provides the possibility to
delay the SDI line latch with one or more core clock cycle. Unfortunatly
the implementation was not correct and the SDI line was latched at the
wrong time.
This patch fix the aligment of the shift register and the SDI_DELAY parameter,
to latch the SDI line of the physical interface at the right time.
Improve the description of the feature.
In some cases, the Vivado version can contain other characters than just
numbers. One such example is after applying the patch of AR# 71948,
which makes `version -short` return something like `2018.3_AR71948`.
This patch changes the version check to ignore anything after the first
two components of the version.
Add definition for new ultrascale device packages.
The package information is used by software for xcvr calibration.
At the moment, the factors that are influencing the calibration for the new
packages are not clear.
The previous mechanism was "probing" the DMAs for valid data. Better said,
each interpolation channel enabled it's DMA until a valid data was received,
then it disabled the DMA read and waited for the adjacent channel(DMA) to
receive a valid data. Only when for both channels had valid data on the
DMAs interfaces was the transmission started. This added an undesired and
redundant complexity to the interpolation channels. Furthermore, for continuous
transmission, using the above mechanism lead to a fixed phase(sample)
shift between the two channels at each start.
By using the streaming mechanism the interface is simplified and the
above problems are solved.
For Intel projects:
In cases where the clock of source synchronous interface is not routed
through a clock capable pin the DPA receive mode can't be used. Instead
the clock will be routed through a clock buffer from an IO to the clock
tree and from there to the IOPLL.
implemented mux for temp reading either from internal or external
source; updated regmap; added param to identify source for temp
information; updated tacho measurements; added AVG_POW param used
for tacho measuremet average useful for simulations; defaults for
tacho measurements changed to params and added registers; added
prescaler for fsm control, FSM updated; changed register write
process; connected INTERNAL_SYSMONE to regmap, value can now be
read by software;
Rodrigo Alencar
Laszlo Nagy
Istvan Csomortani
Stanca Pop
AndreiGrozav
Matt Blanton
Arpadi
Adrian Costina
Mathias Tausen
Maxim