Xilinx tools don't allow to use $clog2() when computing the value of a
localparam, even though it is valid Verilog.
For this reason a parameter was used for BYTES_PER_BURST_WIDTH so far. But
that generates warnings from both Quartus and Vivado since the parameter is
not part of the parameter list.
Fix this by changing it to a localparam and computing the log2() manually.
The upper limit for the burst length is known to be 4k, so values larger
than that don't have to be supported.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
A larger store-and-forward memory provides better protection against worst
case memory interface latencies by being able to store more data before
over-/underflowing.
Based on empirical testing it was found that using a size of 4 bursts can
still result in underflows/overflows under certain conditions. These do not
happen when using a size of 8 bursts.
This change does not significantly increase resource consumption. Both on
Intel and Xilinx the block RAM has a minimum depth of 512 entries. With a
default burst length of 16 beats that allows for up to 32 bursts without
requiring additional block RAM.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
When the source and destination bus widths don't match a resize block is
inserted on the side of the narrower bus. This resize block can contain
partial data.
To ensure that there is no residual partial data is left in the resize
block after a transfer shutdown the resize block is reset when the DMA is
disabled.
Currently this is implemented by tying the reset signal of the resize block
to the enable signal of the DMA. This enable signal is only a indicator
though that the DMA should shutdown. For a proper shutdown outstanding
transactions still need to be completed.
The data that is in the resize block might be required to complete those
transactions. So performing the reset when the enable signal goes low can
lead to a situation where the DMA tries to complete a transaction but can't
do it because the data required to do so has been erased by resetting the
resize block. This leads to a dead lock and the system has to be rebooted
to recover from it.
To solve this use the sync_id signal to reset the resize block. The sync_id
signal will only be asserted when both the destination and source side
module have indicated that they are ready to be reset and there are no more
pending transactions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The width of the AXI burst length field depends on the AXI standard
version. For AXI3 the width is 4 bits allowing a maximum burst length of 16
beats, for AXI4 it is 8 bits wide allowing a maximum burst length of 256
beats.
At the moment the width of the length signals are determined by type of the
source AXI interface, even if the source interface type is not AXI. This
means if the source interface is set to AXI3 and the destination interface
is set to AXI4 the internal width of the signal for all interfaces will be
4 bits. This leads to a truncation of the destination bus length field,
which is supposed to be 8 bits.
If burst are generated that are longer than 16 beats the upper bits of the
length signal will be truncated. The result of this will be that the
external AXI slave interface (e.g. the DDR memory) and the internal logic
in the DMA disagree about burst length. The DMA will eventually lock up
when its internal buffers are full.
To avoid this issue have different configuration parameters for the source
and destination interface that configure the AXI bus length field width.
This way one of the interfaces can be configured for AXI3 and the other for
AXI4 without interfering with each other.
Fixes: commit 495d2f3056 ("axi_dmac: Propagate awlen/arlen width through the core")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Add some limit TLAST support for the streaming AXI source interface. An
asserted TLAST signal marks the end of a packet and the following data beat
is the first beat for the next packet.
Currently the DMAC does not support for completing a transfer before all
requested bytes have been transferred. So the way this limited TLAST
support is implemented is by filling the remainder of the buffer with 0x00.
While the DMAC is busy filling the buffer with zeros back-pressure is
asserted on the external streaming AXI interface by keeping TREADY
de-asserted.
The end of a buffer is marked by a transfer that has the last bit set in
the FLAGS control register.
In the future we might add support for transfer completion before all
requested bytes have been transferred.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The DMAC currently doesn't support transfers where the length is not a
multiple of the bus width. When generating the wstrb signal we do pretend
though that we do and dynamically generate it based on the LSBs of the
transfer length.
Given that the other parts of the DMA don't support such transfers this is
unnecessary though. So remove it for now and replace it with a constant
expression where wstrb is always fully asserted.
The generated logic for the wstrb signal was quite terrible, so this
improves the timing of the core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Currently the read side of the src_response interface is not used. This
leads to warnings about signals that have a value assigned but are never
read.
To avoid this just comment out all signals that are related to the
src_response interface for now.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Make sure the req_gen_valid and req_gen_ready signals are declared before
they are used. Strictly speaking the current code is correct and synthesis
correctly, but declaring the signals make the intentions of the code more
explicit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
All the hdl (verilog and vhdl) source files were updated. If a file did not
have any license, it was added into it. Files, which were generated by
a tool (like Matlab) or were took over from other source (like opencores.org),
were unchanged.
New license looks as follows:
Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
Each core or library found in this collection may have its own licensing terms.
The user should keep this in in mind while exploring these cores.
Redistribution and use in source and binary forms,
with or without modification of this file, are permitted under the terms of either
(at the option of the user):
1. The GNU General Public License version 2 as published by the
Free Software Foundation, which can be found in the top level directory, or at:
https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
OR
2. An ADI specific BSD license as noted in the top level directory, or on-line at:
https://github.com/analogdevicesinc/hdl/blob/dev/LICENSE
Currently the AXI address width of the DMA is always 32-bit. But not all
address spaces are so large that they require 32-bit to address all memory.
Extract the size of the address space that the DMA is connected too and
configure reduce the address size to the minimum required to address the
full address space.
This slightly reduces utilization.
If no mapped address space can be found the default of 32 bits is used for
the address.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Depending on whether the core is configured for AXI4 or AXI3 mode the width
of the awlen/arlen signal is either 8 or 4 bit. At the moment this is only
considered in top-level module and all other modules use 8 bit internally.
This causes warnings about truncated signals in AXI3 mode, to resolve this
forward the width of the signal through the core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Drive all output pins of the disabled interfaces with a constant value.
This avoids warnings from the tools about not driven output ports.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Mark all unused output ports explicitly as explicitly. This makes it clear
that they are left unconnected on purpose and avoids warnings from the
tools about unconnected ports.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
For the source controller use the pause signal that has been properly
transferred to the source clock domain rather than the pause signal from
the request clock domain.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
This control signal can be overwritten by the up_axis_xlast/up_axis_xlast_en bits, in order to create a single stream, which is contains multiple streams.
This can be use to fill up the DACFIFO module.
While the reset for the memory mapped AXI master is synchronous to some
clock it is not necessarily synchronous to the clock used for that
interface. So always generate a local reset signal to avoid problems that
could result from this.
While we are at it also update the code to only generate a local reset if
the interface is asynchronous to the register map, otherwise use the
register map reset.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The src_response_fifo has been removed from the design, but we still need to
assert the ready and empty control signals for things to work properly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
All the FPGA internal control signals are active high, using a active low
reset inserts a extra invert LUT. By using a active high reset we can avoid
that.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Instead of just marking all clock domains as asynchronous set the
appropriate constraints for each CDC path.
For single-bit synchronizers use set_false_path to not constraint the path
at at all.
For multi-bit synchronizers as used for gray counters use set_max_delay with
the source clock period domain to make sure that the signal skew will not
exceed one clock period. Otherwise one bit might overtake another and the
synchronizer no longer works correctly.
For multi-bit synchronizers implemented with hold registers use
set_max_delay with the target clock period to make sure that the skew does
not get to large, otherwise we might violate setup and hold time.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Bring back the AXIS FIFO as a separate module instead of embedding it into
the DMAC module. This makes it possible to use it in other modules outside
of the DMAC.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Move the axi_repack block to its own module. This allows it to use it
outside of the DMA controller.
Also rename it to util_axis_resize to better reflect its function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
When the DMA controller gets disabled in the middle of a transfer it is
possible that the resize block contains a partial sample. Starting the next
transfer the partial sample will appear the begining of the new stream and
also cause a channel shift.
To avoid this make sure to reset and flush the resize blocks when the DMA
controller is disabled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
We need to make sure to not prematurely de-assert the s_valid signal for the
request splitter when disabling the DMAC. Otherwise it is possible that
under certain conditions the DMAC is disabled with a partially accepted
request and when it is enabled again it will continue in an inconsistent
state which can lead to transfer corruption or pipeline stalls.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
All components should use the internal 'do_enable' signal instead of the
external 'enable' signal. The former correctly incorporates the shutdown
sequence and does not get asserted again until the shutdown has been
completed. Using the external signal can cause problems when it is disabled
and enabled again in close proximity.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Vivado 2014.4 is too greedy, when it needs to optimize. See more about the issue here: https://ez.analog.com/thread/48214
The response_dest_resp is unused, so not save to concatenate with a valid signal like the eot.
Make sure that the address generator behaves correctly when the buswidth is not
64-bit. Also since the source and destination can have different widths add
separate parameters for source and destination address alignment.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
There were a few place in the core where it assumed a 64-bit wide bus. Make this
configurable using parameters. The patch also adds support for having different
DMA bus widths on the source and destination side.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Lars-Peter Clausen
Laszlo Nagy
Istvan Csomortani
Rejeesh Kutty
Adrian Costina