Common basic steps:
- Include/create infrastructure:
* Intel:
- require quartus::device package
- set_module_property VALIDATION_CALLBACK info_param_validate
* Xilinx
- add bd.tcl, containing init{} procedure. The init procedure will be
called when the IP will be instantiated into the block design.
- add to the xilinx_blockdiagram file group the bd.tcl and common_bd.tcl
- create GUI files
- add parameters in *_ip.tcl and *_hw.tcl (adi_add_auto_fpga_spec_params)
- add/propagate the info parameters through the IP verilog files
axi_clkgen
util_adxcvr
ad_ip_jesd204_tpl_adc
ad_ip_jesd204_tpl_dac
axi_ad5766
axi_ad6676
axi_ad9122
axi_ad9144
axi_ad9152
axi_ad9162
axi_ad9250
axi_ad9265
axi_ad9680
axi_ad9361
axi_ad9371
axi_adrv9009
axi_ad9739a
axi_ad9434
axi_ad9467
axi_ad9684
axi_ad9963
axi_ad9625
axi_ad9671
axi_hdmi_tx
axi_fmcadc5_sync
Xilinx:
When calling adi_auto_fpga_spec_params in the x_ip.tcl, parameters like
- FPGA_TECHNOLOGY
- FPGA_FAMILY
- SPEED_GRADE
- DEV_PACKAGE
- XCVR_TYPE
- FPGA_VOLTAGE
will be automatically detected and constrained to predefined pairs of values
from adi_xilinx_device_info_env.tcl
The parameters specified in the blobk diagram of the IP(bd.tcl), will be
automatically assign when the IP is added to a block design.
The "adi_auto_assign_device_spec $cellpath" is called in the init
hook (bd.tcl).
https://www.xilinx.com/products/technology/high-speed-serial.html
Intel:
Info parameters are set in the VALIDATION_CALLBACK according to
adi_intel_device_info_env.tcl
Fix the following warning:
WARNING: [Synth 8-2611] redeclaration of ANSI port up_es_reset is not allowed
Also make sure, that in all configurations, the register has a diver.
Add support for 8 bit resolution for the transport layer.
Fix parameter BITS_PER_SAMPLES propagation to all the internal modules, in
several cases this variable was hard coded to 16.
The axi_pulse_gen is a generic PWM generator, which can be configured
through an AXI Memory Mapped interface.
The current register map look like follows:
0x00 - VERSION
0x04 - ID
0x08 - SCRATCH
0x0C - IDENTIFICATION - 0x504c5347 which stands for 'PLSG' in ASCII
0x10 - CONFIGURATION - contains reset and load bits
0x14 - PULSE_PERIOD
0x18 - PULSE_WIDTH
Also update all the other modules, which instantiate the util_pulse_gen.
To prevent the case, when after an invalid configuration, the generated
output PWM signal is constant HIGH, change the counter to a
down-counter. In this way the pulse will be placed at the end of the
PWM period, and if the configured width value is higher than the
configured period the output signal will be constant LOW.
In the current form, when connecting a master to the HP ports all
available slave address spaces are mapped to the master (DDR_*, PCIE*, OCM,
QSPI)
Let the PL masters have access only to the DDR_LOW and DDR_HIGH address
spaces to avoid unnecessary resource usage and increase timing margin.
Write code to pipeline data path for better DSP utilization on the
color space conversion.
In the old method the addition operations were performed outside the
DSPs
The FIFO functions in 'first fall through' mode, adjust the fifo level
generation so it take into account the valid data which sits on the bus,
waiting for ready, too.
Create the dacfifo/adcfifo infrastructure with procedures.
This will allow moving the parameters of the dac/adcfifo inside
the block design so it can be calculated based on other parameters.
AndreiGrozav
Adrian Costina
Istvan Csomortani
sarpadi
Sergiu.Arpadi
Laszlo Nagy