044017e0b9
ad9081_fmca_ebz/zcu102: Make second sync CMOS and GPIO controllable
2022-05-11 18:09:08 +03:00
97b92565b2
Makefile: Replace util_fifo2axi_bridge with util_hbm
2022-04-28 14:31:32 +03:00
fa168fafe0
ad9081_fmca_ebz:vcu128: Disable offload bypass
...
The internal bypass FIFO has poor timing performance,
when using HBM data can be passed always through the external memory
without storage length constraints, so no need for the internal bypass FIFO.
2022-04-28 14:31:32 +03:00
c57015f80e
ad9081_fmca_ebz/vcu128: Use HBM for data offload cores
2022-04-28 14:31:32 +03:00
dbadb9eb61
ad9081_fmca_ebz/common: Make data offload memory type selectable
...
Make the storage type over writable so it can be set specifically
to carriers.
Address width of external memory AXI master is calculated in the
interfacing core (util_hbm) so that parameters is removed.
2022-04-28 14:31:32 +03:00
638491d502
projects: ad9081: Disable tdd_sync CDC sync of TDD controller
...
Signed-off-by: David Winter <david.winter@analog.com>
2022-04-20 10:54:53 +03:00
8df1d8eade
ad9081_fmca_ebz: Update parameter description
2022-03-11 13:16:22 +02:00
45dae0f3d3
ad9081_fmca_ebz/common: Connect sync at TPL level
...
Reset CPACK from ADC TPL so during armed capture clear the cpack to avoid
capturing old samples.
Reset UNPACK with TPL to clear upack during armed transfers to avoid
sending old data.
2022-02-07 19:14:01 +02:00
77f3e5155b
ad9081_fmca_ebz: Fix signal length parameter
...
Corrected the length parameter for the rx_data input.
Signed-off-by: Dan Hotoleanu <dan.hotoleanu@analog.com>
2021-12-08 14:29:48 +02:00
80b3fc2d0a
ad9081_fmca_ebz: versal: Remove unused GT reset input pin
...
Signed-off-by: Laszlo Nagy <laszlo.nagy@analog.com>
2021-11-22 16:18:29 +02:00
1ec0993d33
ad9081_fmca_ebz/vcu128: Remove ref clock replica
...
Signed-off-by: Laszlo Nagy <laszlo.nagy@analog.com>
2021-11-22 16:18:29 +02:00
e76f287e73
ad9081_fmca_ebz:vcu128: Initial version
...
* 4Txs / 4Rxs per MxFE
* Tx I/Q Rate: 250 MSPS
* Rx I/Q Rate: 250 MSPS
* DAC JESD204B: Mode 9, L=4, M=8, N=N'=16
* ADC JESD204B: Mode 10, L=4, M=8, N=N'=16
* DAC-Side JESD204B Lane Rate: 10Gbps
* ADC-Side JESD204B Lane Rate: 10Gbps
2021-11-19 18:08:16 +02:00
e00def31d0
ad9081_fmca_ebz: versal: Remove external gt_reset logic
2021-11-19 14:01:48 +02:00
0b9631f1f7
ad9081_fmca_ebz: versal: Rename nets
2021-11-19 14:01:48 +02:00
ca6248ba88
ad9081_fmca_ebz/common/versal_transceiver.tcl: Reset also PLL
2021-11-19 14:01:48 +02:00
731ed0a7a5
ad9081_fmca_ebz/vck190: Updated to hierarchical versal transceiver
...
Vivado cannot nest multiple block designs than two layers. This makes
replication of designs difficult.
Create a hierarchy around the Versal transceiver that includes also the
converters, this type of interface would match the util_adxcvr
interface.
Signed-off-by: Laszlo Nagy <laszlo.nagy@analog.com>
2021-11-19 14:01:48 +02:00
1d951cfbae
ad9081_fmca_ebz/vck190: Change default profile to 2 lanes
2021-11-19 14:01:48 +02:00
adad6c930d
ad9081_fmca_ebz_qsys.tcl: Add RX_LANE_RATE and TX_LANE_RATE parameters
...
For ad9081/a10soc project, the RX_LANE_RATE and TX_LANE_RATE were computed
from SAMPLE_RATE. Remove SAMPLE_RATE and add RX_LANE_RATE and TX_LANE_RATE
as parameters. Update also computation examples from comments.
Signed-off-by: stefan.raus <stefan.raus@analog.com>
2021-11-12 13:04:57 +02:00
63b6711cfa
start adding some doc to the ./projects directory
...
This adds a Readme.md to each project directory with pointers to project
documentation in the wiki, and the drivers (if they exist). This will
help with some autogenerated doc in the wiki, that is generated with the
innovatily named "wiki_summary.sh" shell script that parses through
these Readme.md files, and generates a summary table.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Iacob Liviu Mihai <liviu.iacob@analog.com>
2021-11-10 14:01:06 +02:00
9295218a64
projects/ad9081_fmca_ebz: Updated makefiles
2021-10-05 16:56:57 +03:00
51b643b978
Makefile: Fix misc makefiles from projects and library
2021-10-05 14:24:48 +03:00
3a1babe366
ad9081_fmca_ebz/vck190: Reset GT with HMC7044 lock
...
Reset transceiver with a pulse
2021-10-05 14:09:51 +03:00
2562aead32
ad9081_fmca_ebz/common: Drive Rx DMA system side with DMA clock
2021-10-05 14:09:51 +03:00
8d547f31e1
ad9081_fmca_ebz/vck190: Initial version
2021-10-05 14:09:51 +03:00
6c58a8d1ab
ad9081_fmca_ebz/common: Add Versal transceiver support
2021-10-05 14:09:51 +03:00
edd2956d58
data_offload: Fix util_[cu]pack offset to TDD syncs
...
Signed-off-by: David Winter <david.winter@analog.com>
2021-09-30 14:45:54 +03:00
b9554a9a5a
ad9081_fmca_ebz: Integrate axi_tdd into zcu102 design
...
Signed-off-by: David Winter <david.winter@analog.com>
2021-09-30 14:45:54 +03:00
591a23156b
Makefiles: Update header with the appropriate license
2021-09-16 16:50:53 +03:00
e9e278c898
ad9081_fmca_ebz: Remove bypass gpio
...
Signed-off-by: David Winter <david.winter@analog.com>
2021-08-06 11:55:24 +03:00
2178191610
ad9081_fmca_ebz: Switch util_dacfifo to data_offload engine
...
Memory requirements are the same as with the dacfifo (1 MiB).
Signed-off-by: David Winter <david.winter@analog.com>
2021-08-06 11:55:24 +03:00
75b965e87f
ad9081_fmca_ebz/zcu102: Enable 204C modes
2021-06-10 09:53:43 +03:00
27465ce9c0
ad9081_fmca_ebz/zcu102: Fix spaces
2021-06-10 09:53:43 +03:00
0ad691a603
ad9081_fmca_ebz/zcu102: Differentiate parameters based on lane rate
2021-05-14 15:39:40 +03:00
8183599b51
ad9081_fmca_ebz/zcu102: Fix typo
2021-05-14 15:39:40 +03:00
cf7f45ffcc
ad9081_fmca_ebz: Fix for F=8
2021-05-14 15:39:40 +03:00
7b2ba41bdd
ad9081_fmca_ebz/vcu118: Adjust QPLL params and diff swing
...
This commit fixes the 16.5Gbps lane rate case where the link drops
after few seconds an initial successful link up happens.
A few seconds delayed calibration process can workaround this but with
having the differential drivers swing increased this is no longer
required.
2021-05-14 15:39:40 +03:00
0d9e38bdbe
ad9081_fmca_ebz: Update path to common block design
...
Use absolute paths so ad9082 wrapper project can include the
system_bd.tcl instead of duplicating code.
2021-05-14 15:39:40 +03:00
680d28476c
ad9081_fmca_ebz: Add LANE_RATE param to all projects
...
The block design expects a lane rate to be set in the system project.
2021-05-14 15:39:40 +03:00
bd6ec360e2
ad9081_fmca_ebz/vcu118: Set XCVR params for 204C link
...
Set XCVR parameter for 204C 24.75 Gbps with a dynamic range of 10Gbps..24.75Gpbs
Organize XCVR params based on lane rate
2021-05-14 15:39:40 +03:00
693c002668
ad9081_fmca_ebz/common/ad9081_fmca_ebz_bd: Add 204C support for XCVR
...
Remove Xilinx PHY and simplify project
2021-05-14 15:39:40 +03:00
d92f925b06
ad9081_fmca_ebz: Disable XBAR from DAC TPL
2021-05-14 15:39:40 +03:00
4a772265a9
Update Quartus Prime version from 19.3.0 to 20.1.0
...
adi_project_intel.tcl: Change quartus version to 20.1.0.
library: Set qsys version so that IP instances won't require a specific version.
2021-03-08 11:29:33 +02:00
6b13b32f24
ad9081_fmca_ebz: Workaround DMA bug when bus size equals max burst size
2021-03-04 11:13:29 +02:00
0374a7c1ac
ad9081_fmca_ebz/vcu118: Added common 204C use cases as example
2021-02-05 15:24:15 +02:00
ddd8a14790
ad9081_fmca_ebz: Remove system reset from Xilinx PHY
...
Reset in device clock domain caused timing failures.
Since link reconfiguration is not supported the reset is not required.
2021-02-05 15:24:15 +02:00
af3e1c7003
ad9081_fmca_ebz/a10soc: Np 12 support
2021-02-05 15:24:15 +02:00
bb9eafceef
ad9081_fmca_ebz/zcu102: Add case analysis to select correct out clock frequency
2021-02-05 15:24:15 +02:00
d0f8a81b2f
ad9081_fmca_ebz: Np 12 support
...
204B functional
204C functional
2021-02-05 15:24:15 +02:00
0fd5590e56
ad9081_fmca_ebz: a10soc: Initial version
...
Parametrizable project with default profile of:
M=8 L=4 SampleRate=250 MSPS
LaneRate=10 Gbps
2021-02-05 10:24:59 +02:00
6f2f2b8626
makefile: Regenerate make files
2021-01-20 01:02:56 +02:00
Laszlo Nagy
David Winter
Dan Hotoleanu
stefan.raus
Robin Getz
Filip Gherman
Adrian Costina
Sergiu Arpadi