Fix the read side of the CDC data FIFO. The read address generation did not
function correctly.
Redesign the read side of the FIFO, and make sure that it becomes empty after
the DMA transfer ends; and never get stock in a cyclic mode.
The dac_last signal is not used anywhere in the module. Remove it and its
synchronization registers.
Fixes the following warnings:
[Synth 8-6014] Unused sequential element dac_dlast_reg was removed. ["axi_dacfifo_rd.v":372]
[Synth 8-6014] Unused sequential element dac_dlast_m1_reg was removed. ["axi_dacfifo_rd.v":373]
[Synth 8-6014] Unused sequential element dac_dlast_m2_reg was removed. ["axi_dacfifo_rd.v":374]
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Commit bfc8ec28c3 ("util_axis_fifo: instantiate block ram in async mode")
added the read-enable (reb) signal to the ad_mem block.
It didn't update the ad_mem instance in axi_dacfifo_address_buffer.v. This
results in the read-enable of the address_buffer being tied to 0.
Fix this by connecting the same signal that increments the read address.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Currently the individual IP core dependencies are tracked inside the
library Makefile for Xilinx IPs and the project Makefiles only reference
the IP cores.
For Altera on the other hand the individual dependencies are tracked inside
the project Makefile. This leads to a lot of duplicated lists and also
means that the project Makefiles need to be regenerated when one of the IP
cores changes their files.
Change the Altera projects to a similar scheme than the Xilinx projects.
The projects themselves only reference the library as a whole as their
dependency while the library Makefile references the individual source
dependencies.
Since on Altera there is no target that has to be generated create a dummy
target called ".timestamp_altera" who's only purpose is to have a timestamp
that is greater or equal to the timestamp of all of the IP core files. This
means the project Makefile can have a dependency on this file and make sure
that the project will be rebuild if any of the files in the library
changes.
This patch contains quite a bit of churn, but hopefully it reduces the
amount of churn in the future when modifying Altera IP cores.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
This reduces the amount of boilerplate code that is present in these
Makefiles by a lot.
It also makes it possible to update the Makefile rules in future without
having to re-generate all the Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Redesign the axi_dacfifo, to increase the supported datarates.
Major modifications:
+ The FIFO consist of two module: WRITE and READ. The axi_dacfifo_dac
was deprecated.
+ Both the AXI write and AXI read transaction are controlled by two
FSM, to increase redability of the code.
+ Support all the possible burst lengths [0..225], handles the last
fractional burst on both sides correctly.
+ Common reset architecture throughout the design, all the internal
registers and memories are reset on the posedge of dma_xfer_req
+ Delete all Altera related sources, for Altera projects
avl_dacfifo should be used.
WIP: foobar
[WIP]axi_dacfifo: Update
axi_dacfifo: Few minor updates, almost working state
Increase the width of wvalid_counter, should be equal with awlen width.
The wvalid_counter needs to count from zero to the required burst
length. The maximum burst length is 255, so the width of the counter
have to be 8 bits. axi_last_beats will get the last axi burst length.
The fifo will ask for a new data from the DDR, if the current
level is lower than the high threshold. This will prevent overflow.
By deleting the lower threshold, we can avoid ocassional underflows,
when the DAC rate is closer to the max DDRx rate.
Fix the dma_ready mux in top module, and the dma_ready_out reset
logic in axi_dacfifo_wr module. Also, both write and read addresses
of the async CDC fifo (inside the axi_dacfifo_wr) should be reset
before a dma transaction starts.
All the hdl (verilog and vhdl) source files were updated. If a file did not
have any license, it was added into it. Files, which were generated by
a tool (like Matlab) or were took over from other source (like opencores.org),
were unchanged.
New license looks as follows:
Copyright 2014 - 2017 (c) Analog Devices, Inc. All rights reserved.
Each core or library found in this collection may have its own licensing terms.
The user should keep this in in mind while exploring these cores.
Redistribution and use in source and binary forms,
with or without modification of this file, are permitted under the terms of either
(at the option of the user):
1. The GNU General Public License version 2 as published by the
Free Software Foundation, which can be found in the top level directory, or at:
https://www.gnu.org/licenses/old-licenses/gpl-2.0.en.html
OR
2. An ADI specific BSD license as noted in the top level directory, or on-line at:
https://github.com/analogdevicesinc/hdl/blob/dev/LICENSE
Adrian Costina
Istvan Csomortani
Laszlo Nagy
Lars-Peter Clausen
Rejeesh Kutty