Update vivado version to 2020.2:
- update default vivado version from 2020.1 to 2020.2
- add conditions to apply specific contraints only in Out Of Context mode.
- update DDR controler parameters for vcu118 and kcu105 dev boards
The width of the parameter `device_cfg_octets_per_multiframe` doesn't match the width in the submodules and corresponding slave module jesd204_tx, resulting in a warning generated during validation in Vivado. This patch increases the width of this parameter in axi_jesd204_tx.
Fix offset for pwms with different periods.
The previous version was using an offset scheme based on pwm counter_0.
By using a separate offset counter the user will not be constrained by
pwm_0 period in regards with the offset of other pulses. In this version
offset 0 is used to delay pwm 0 in regards to the offset counter.
The offset counter will start after the load_config signal is asserted
and all active pwm counters finish the previous cycle or by a software
reset.
The software reset should also be used when using external_sync.
* fixes DRC warning that the clocking configuration may result in data errors
* fixes ioserdes reset issue with synchronous de-assert in data clock domain
This commit adds a standalone TDD IP core based on the
existing up_tdd_cntrl module and the up_axi pcore <-> axi bridge.
Signed-off-by: David Winter <david.winter@analog.com>
If all channels are selected for read the values and ready signals from every
transceiver are combined. Each element merges his signals with the previous.
The first element of the chain must assume the previous channel is always ready.
This reverts commit 829e4155ca.
The first element of the read chain must assume there is no valid element
in front of it. For each element the ready signal of the transceiver should be
routed if the channel is selected either by channel number or broadcast.
When the current element is not selected it should forward the ready signal from
the previous element, however this is not the case for the first one.
Having a constant 1'b1 connected to the ready input of the first element
corrupts the first read of the first channel after a channel switch.
This change will break broadcast reads.
Adds a magic identification value of 0x54444443 at word address 0x3.
It is derived from the ASCII String "TDDC" interpreted as a big-endian
32-bit unsigned integer.
Signed-off-by: David Winter <david.winter@analog.com>
For GTH3/4 64b66b mode add a second clock that drives CLKUSR with a clock
that is 2x of the CLKUSR2 (lane rate/66),
CLKUSR = 2 x CLKUSR2
CLKUSR = lane rate / 33
This can be driven from the GT reference clock or second out clock div2.
This commit also:
- fix eyescan scale on GTY
- remove irrelevant parameters
If R1 mode is first syncronized to the dac clock domain will prevent its
usage if the dac clock is missing. In such case the synchronization will not
propagate.
Depending on FPGA technology the physical layer uses different
deserialization factors and corresponding clock division factors to
divide the source synchronous interface clock. This must be
exposed to software so it can act on it while setting the DDS rate.
Xilinx CMOS clock ratio - 4
Xilinx LVDS clock ratio - 4
Intel CMOS clock ratio - 1
This module creates sync header alignment described in section 7.6.1 of
the JESD 204C specification.
The alignment relies on the bitslip capability of the connected
transceiver.
Create a common 'run_tb.sh' script to be called by every testbench.
Unify file and testbenches names.
Fix util_pack/cpack_tb.
Add parameters '-batch' and '-gui' for modelsim and xsim simulators (default is gui)
Add ascript for that generates output in xml format (used by CI tools).
Istvan Csomortani
Nick Pillitteri
stefan.raus
Isaac T
Laszlo Nagy
AndreiGrozav
Iacob_Liviu
Josh Blum
alin724
David Winter
Alin-Tudor Sferle