72f916fcf5
adrv9001/zcu102: Update interface signal names based on direction
...
Let the names of signals from source synchronous interface match the
direction of the signals.
2020-08-28 13:23:00 +03:00
a212ad6e58
adrv9001/zed: Update interface signal names based on direction
...
Let the names of signals from source synchronous interface match the
direction of the signals.
2020-08-28 13:23:00 +03:00
eb2f211d30
scripts/intel: Add message severity definition file
2020-08-25 14:46:52 +03:00
9c4df588bb
fmcomms2: a10soc remove project
...
Starting from Quartus 18.1 the project won't build as LVDS SERDES needs to be
driven by a dedicated reference clock pin and A10SOC doesn't have dedicated pins
routed at the _CC FMC location.
Prior to version 18.0 this was reported as a critical warning.
See https://community.intel.com/t5/Intel-Quartus-Prime-Software/LVDS-SERDES-reference-clock-enforcement-change-in-18-1/td-p/196078
2020-08-25 14:19:48 +03:00
118e1f9e8b
adrv9001/zed: Initial support for Zed
...
CMOS only support for ADRV9001 on ZedBoard
2020-08-24 17:49:12 +03:00
b27f3ac18f
adrv9001:zcu102: Initial version
...
Generic project that supports CMOS or LVDS interface for the ADRV9001 transceiver.
2020-08-24 17:49:12 +03:00
d8c98c9904
cn0540/coraz7s: Relax timing in SPI Engine
2020-08-24 16:45:02 +03:00
fa0b39fa20
adi_project_intel: Update QSYS generation
...
In Quartus Prime in place of the set_domain_assignment command, the
set_interconnect_requirement command is used.
2020-08-17 12:02:49 +03:00
b54effc9c9
daq2/a10gx: Set optimization mode to aggressive performance
2020-08-17 10:43:03 +03:00
fb7da01498
adrv9371x/a10gx: Set optimization mode to aggressive performance
2020-08-17 10:43:03 +03:00
738f7af23b
ad40xx_fmc: SDI delay should be set to 1
...
In general we have to add a delay of half SCLK cycle.
(latch the MISO on the next consecutive SCLK edge)
2020-08-13 10:01:16 +03:00
4766d01915
m2k: Update constraints
2020-08-13 07:01:19 +03:00
4d39a3595f
m2k: Connect signals for instrument sync
2020-08-13 07:01:19 +03:00
f3b69c15c9
scripts/intel: Update version check
2020-08-12 10:33:29 +03:00
218f45a0df
scripts/intel: Set supported Quartus version to 19.3
2020-08-12 10:33:29 +03:00
62eb5a067d
fmcomms2/a10soc: Unused outputs should be left hanging
2020-08-11 10:14:18 +03:00
a66029aef3
adrv9009/a10gx: Delete redundant timing constraints
2020-08-11 10:14:18 +03:00
02ada3bbf7
a10gx: Delete input/output delay definitions
...
All input and output delays should be referenced to a virtual clock.
If the input and output delays reference base clocks or PLL clocks rather than
virtual clocks, the intra- and inter-clock transfer clock uncertainties,
determined by derive_clock_uncertainty, are incorrectly applied to the I/O ports.
See mnl_timequest_cookbook.pdf for more info.
2020-08-11 10:14:18 +03:00
f1a0946a5d
daq3: Delete redundant timing constraint
...
Delete none generic timing constarints related to the memory interface.
Set optimization mode to default.
2020-08-11 10:14:18 +03:00
1c907b9248
daq2/a10gx: Use the default optimization mode
2020-08-11 10:14:18 +03:00
9043f3737b
Revert "a10gx: Optimise the base design"
...
This reverts commit 9afc871b70
2020-08-11 10:14:18 +03:00
4af0c98c56
a10gx: Fix exceptionSlave interface definition for HPS
2020-08-11 10:14:18 +03:00
5ba3448987
scripts/project-intel: Update CLEAN target
2020-08-11 10:14:18 +03:00
0b51c474a1
a10gx: Add a Avalon Pipeline Bridge between EMIF and DMA's
2020-08-11 10:14:18 +03:00
6d19041b21
dac_fmc_ebz: QPRO is using apply_instance_preset
2020-08-11 10:14:18 +03:00
0de5039b96
avl_dacfifo: add_intance command must have a version attribute
2020-08-11 10:14:18 +03:00
8fd1ad64d6
quartus: Increase tool version to 19.2
2020-08-11 10:14:18 +03:00
f3142a6a7a
adi_project_intel: set_interconnect_requirment command is deprecated
...
Use set_domain_assignment to set up the maximum pipeline stages for the
main interconnect.
2020-08-11 10:14:18 +03:00
a39fa831d0
ad9371:a10gx: Relax interconnect requirements
2020-08-11 10:14:18 +03:00
7e22f91429
adrv9371:a10gx: Remove constraint from DDR
2020-08-11 10:14:18 +03:00
359e5d94ec
a10gx: Remove constraint from eth_ref_clk
2020-08-11 10:14:18 +03:00
967a138d0f
adi_project_intel: Add support for Quartus Pro
...
By defualt the supported tool chain is Quartus PRO. If you want to
build the project with Quartus Standard, you need to define an environment
variable called QUARTUS_PRO_ISUSED with the value 0. (e.g. export
QUARTUS_PRO_ISUSED=0 )
Note: Not all projects going to build on Quartus Standard, you should
fix the errors if there is any.
2020-08-11 10:14:18 +03:00
054193e083
adi_project_intel: Delete all MESSAGE_DISABLE assignment
...
These kind of assignments should be placed into file like
~/projects/scripts/adi_xilinx_msg.tcl
2020-08-11 10:14:18 +03:00
4ca1311d57
quartus_pro: Global assignment ENABLE_ADVANCED_IO_TIMING is not supported
2020-08-11 10:14:18 +03:00
8d6b8fc631
Add cn0506_rmii/zcu102 support on revB
2020-08-10 18:32:44 +03:00
7e96514230
Add cn0506_rmii/zc706 support on revB
2020-08-10 18:32:44 +03:00
321b82398b
Add cn0506_rmii/zed support on revB
2020-08-10 18:32:44 +03:00
6c2b1b1634
fmcomms5/zc702: Fix the sys_dma_clk connections
2020-06-19 12:53:18 +03:00
137c31db1d
daq2/xilinx: Update project to use generic JESD204 TPL
2020-06-18 15:45:19 +03:00
299273f5a1
daq2/intel: Update project to use generic JESD204B TPL
2020-06-18 15:45:19 +03:00
847f0f22e6
cn0540: Fix typo
2020-06-04 18:38:14 +03:00
193fce338d
cn0540: Initial commit
2020-05-28 18:49:35 +03:00
03ab28d7bf
ad77681evb: Remove coraz7s project
2020-05-28 18:49:35 +03:00
71d500bdd4
adrv9009/intel: Use generic TPL cores
2020-05-26 16:22:30 +03:00
9c8190f709
adi_project_xilinx.tcl: discover all timing failures
...
Look for an overall indicator of timing failure.
Create critical warning if timing is failed.
2020-05-26 14:47:38 +03:00
47a97aac7c
adrv9371x/intel: Update project to use generic JESD204B TPL
2020-05-25 11:55:40 +03:00
e8f6523197
ad9081_fmca_ebz: adapt to renamed tpl core
2020-05-20 19:08:25 +03:00
db6af63583
scripts/adi_env.tcl: print in logs system variables are used
2020-05-20 19:07:23 +03:00
e7600eb552
ad7616_sdz: Fix the project, after SDI ports were merged
...
Update the project to support the SDI port merge patch: 4d54c7e
2020-05-20 11:44:22 +03:00
4d54c7e2d6
spi_engine_execution: Merge the SDI lines into one vector
...
This modification will help to support multiple SPI engine
execution setups (e.g. different NUM_OF_SDI) for the same project.
2020-05-19 09:28:02 +03:00
6535e5b2ba
scripts/xilinx: Version mismatch is upgraded to ERROR
...
There is a major compatibility issue between 2019.1 and 2019.2.
The file system_top.hdf got a different file extention. This will
cause a compilation failer in the end of the build. To save time
and fail earlier, upgrade the version mismatch message to ERROR.
If user still wants to build a branch with different tool version
the variable ADI_IGNORE_VERSION_CHECK should be set to 1.
2020-05-15 12:16:35 +03:00
32eeedb660
makefile: Update makefiles
2020-05-07 08:41:49 +01:00
cbb23c7b67
ad9081_fmca_ebz: fix Xilinx PHY resets
...
Avoid clock domain crossing on resets.
2020-04-23 17:21:05 +03:00
e112a03d85
ad9081_fmca_ebz: Whitespace cleanup
...
Clear extra lines and whitespaces at end of lines.
2020-04-23 17:21:05 +03:00
7df4caf8b0
ad9081_fmca_ebz: Added parameter description
...
Add parameter description to project and common block design file
2020-04-23 17:21:05 +03:00
e433d3f808
ad9081_fmca_ebz: expose PLL selection as a parameter
...
On the Xilinx PHY the available PLL options depends on the lane rate.
Encoding is:
0 - CPLL
1 - QPLL0
2 - QPLL1
Since the selection of line rate is available from the project also the
PLL selection must be exposed.
2020-04-23 17:21:05 +03:00
b774e1ca7d
ad9081_fmca_ebz: enable IQ rotation
2020-04-03 11:16:37 +03:00
4684dc03ce
dac_fmc_ebz/a10soc: Use balanced optimization mode
...
Always a good idea to start from default, and change optimization mode
of the tool if it's strict necessary.
2020-03-17 17:25:02 +00:00
253a8cb6ee
dac_fmc_ebz/a10soc: Tool expect that all config parameters exists on top entity
2020-03-17 17:25:02 +00:00
522aacf6d8
ad_fmclidar1_ebz/a10soc: Fix AFE's I2C interface
...
The AFE's I2C interface should be pin-multiplexed to the FPGA. Also, add
a bidirectional IO buffer for the interface, and make sure it has weak
pull-up resistors.
2020-03-17 07:27:49 +00:00
19b7986486
fmcomms8: Fix SPI timing
...
The maximum SPI rate set to 10MHz
2020-03-16 13:26:20 +02:00
fde79a2272
ad_fmclidar1_ebz: Fix AFE's SPI polarity
2020-03-10 16:37:18 +00:00
b1f62f09ac
ad9081_fmca_ebz:vcu118: initial version
...
Use over-writable parameters from the environment.
e.g.
make JESD_MODE=64B66B RX_RATE=24.75 TX_RATE=12.375 REF_CLK_RATE=375 RX_JESD_L=4 TX_JESD_L=4
make JESD_MODE=64B66B RX_RATE=16.22016 TX_RATE=16.22016 REF_CLK_RATE=245.76 RX_JESD_M=8 RX_JESD_L=2 TX_JESD_M=16 TX_JESD_L=4
make JESD_MODE=8B10B RX_JESD_L=4 RX_JESD_M=8 TX_JESD_L=4 TX_JESD_M=8
2020-03-10 18:19:03 +02:00
f3a7fd8b0d
ad9081_fmca_ebz:zcu102: initial version
2020-03-10 18:19:03 +02:00
f3630dd95b
ad9081_fmca_ebz: common block design
...
Parametrizable block design with selectable JESD physical layer between
Xilinx Phy and ad_utilxcvr.
2020-03-10 18:19:03 +02:00
1f7671cb36
scripts/adi_env.tcl: helper function for environment variables
...
Ease the access of the environment variables.
2020-03-10 18:19:03 +02:00
fad52175d1
fmcomms8: Fix spi connection
2020-03-06 16:07:02 +02:00
50d904934a
fmcomms8: Changed the interrupt addresses to be similar with adrv9009zu11eg project
2020-03-06 16:07:02 +02:00
e1353d5291
m2k: use DMA streaming interface
...
The previous mechanism was "probing" the DMAs for valid data. Better said,
each interpolation channel enabled it's DMA until a valid data was received,
then it disabled the DMA read and waited for the adjacent channel(DMA) to
receive a valid data. Only when for both channels had valid data on the
DMAs interfaces was the transmission started. This added an undesired and
redundant complexity to the interpolation channels. Furthermore, for continuous
transmission, using the above mechanism lead to a fixed phase(sample)
shift between the two channels at each start.
By using the streaming mechanism the interface is simplified and the
above problems are solved.
2020-03-06 15:57:43 +02:00
dd47e30431
ad7768_evb_sync: Fixed sync issue
...
fixed sync inside ad7768_if module;
2020-03-04 18:21:55 +02:00
35412c81a9
dac_fmc_ebz: drive spi_en pin automatically based on FMC board selected
...
spi_en is active ...
... high for AD9135-FMC-EBZ, AD9136-FMC-EBZ, AD9144-FMC-EBZ,
... low for AD9171-FMC-EBZ, AD9172-FMC-EBZ, AD9173-FMC-EBZ
2020-03-03 15:49:30 +02:00
ef15757d9e
common:vcu118: support for plddr4 adc and dac fifo
...
Use 1GB from the DDR4 for either ADC or DAC sample buffering.
Max theoretical bandwidth of 19.2 GB/s
2020-03-03 15:49:11 +02:00
48a91796e2
ad77681evb: Set spi_clk to 40MHz ( #435 )
2020-02-24 12:55:06 +02:00
37188b01d8
fmcomms2:a10soc: use non DPA mode
2020-02-24 11:31:01 +02:00
96b7b3fa5f
fmcomms2: Add support for a10soc
...
Because fmcomms2 was not supported on a Intel carriers the
fmcomms2_qsys.tcl file got outdated.
The arradio project has the same hdl design. Hence the update is
merely a copy of the arradio_qsys.tcl with small changes.
2020-02-24 11:31:01 +02:00
2bca2e156c
cn0506_rgmii: Fix no clock defined warnings
...
This commit fixes the critical warning regarding the missing clock
definitions.
- Defined MDC(MDIO) clocks
- Set false path on(to) the ps8 MDIO input pins. There are synchronization
stages in the GMII to RGMII converter for the CDC between the 375M refclk
and 2.5M MDC clock domains.
2020-02-21 18:22:49 +02:00
6d91e2e54f
coraz7s_fix: Tied drdy to gpio
...
removed IOB attribute for drdy
2020-02-18 13:24:43 +02:00
501abfd53a
common/coraz7s: Fixed ethernet issue
...
fixed coraz7s preset; cleaned up lines which generated warnings
2020-02-18 13:24:43 +02:00
c4b94fc564
adrv9009zu11eg: Add S JESD204 parameter for the projects
2020-02-18 11:19:02 +02:00
645696e5b4
adrv9009zu11eg: Extend SPI connection to the PL HD PINS expansion
2020-02-18 11:19:02 +02:00
d2817863a1
adrv9009zu11eg: Add FMCOMMS8 support
2020-02-18 11:19:02 +02:00
29f18e501e
adrv9009zu11eg: Cleanup bd file
2020-02-18 11:19:02 +02:00
3192807f22
adi_project_xilinx: Fixed variable name
2020-02-14 11:22:46 +02:00
c5e03eb196
adi_project_xilinx: Added power analysis procedure
2020-02-14 11:22:46 +02:00
74fc68d4c3
axi_fan_control: Changed temperature thresholds to registers
...
implemented mux for temp reading either from internal or external
source; updated regmap; added param to identify source for temp
information; updated tacho measurements; added AVG_POW param used
for tacho measuremet average useful for simulations; defaults for
tacho measurements changed to params and added registers; added
prescaler for fsm control, FSM updated; changed register write
process; connected INTERNAL_SYSMONE to regmap, value can now be
read by software;
2020-02-14 11:21:12 +02:00
78a1e54a33
adi_project_xilinx.tcl: Generate resource utilization for IPs
2020-02-13 11:33:02 +02:00
46a413d9a5
dac_fmc_ebz/common/config.tcl: fix typo
2020-02-13 11:32:38 +02:00
e51d9372cd
fmcomms8: ZCU102: Added DAC FIFO
2020-02-10 11:23:52 +02:00
016a1d540d
fmcomms8: ZCU102: Initial commit
2020-02-10 11:23:52 +02:00
10a808b504
ad9208_dual_ebz/vcu118: remove GTY prefix from parameters
2020-02-10 09:48:17 +02:00
05c20af988
Merge pull request #430 from analogdevicesinc/update_tcl
...
Rename projects for consistency
2020-02-06 16:32:40 +02:00
e00ee136f6
cn0506_mii Updates for Rev B board
...
Because of the rmii mode requirements(external 50MHz clock) the
board will have the rx_err signal replaced on the FMC connector with the
50MHz external clock (D08/D20).
The rx_er will be shifted to the D9/D21 pins.
2020-02-03 11:20:18 +02:00
b3e475cb8b
ad_fmclidar1_ebz: Update the IO constraints to revB
...
The IO location of the laser_driver_otw_n was moved from FMC_HPC_LA27_N
to FMC_HPC_LA31 (laser_gpio[12]).
laser_gpio[11:0] assignments were shifted with one bit to MSB, and laser_gpio[0]
got the old location of the laser_driver_otw_n.
2020-01-31 18:47:37 +02:00
135538b521
adi_project: Fixed kcu105 board file selection
2020-01-16 17:16:58 +02:00
db5e21cfb9
pluto revC: Add second RF channel
...
-add second RF channel (without fir filters)
-use a more generic instantiation of the fir filters
-add util_cpack2 and util_upack2
2020-01-16 11:40:28 +02:00
f9c8ff26cf
pluto rev C hardware updates
...
-connect axi_spi to board GPIOs
-connect axi IIC to board GPIOs
MIO49 SPI_CS (PS MIO49)
L10P SPI_MOSI (AXI_SPI)
L12N SPI_MISO (AXI_SPI)
L24N SPI_CLK (AXI_SPI)
L7N iic_sda (AXI_IIC)
L9N iic_scl (AXI_IIC)
2020-01-16 11:40:28 +02:00
e773b22087
adi_project: Updated board files version selection
...
vivado will automatically select the latest version for a given board
2020-01-14 17:16:01 +02:00
fcf7bb035a
ad40xx: Fix data_width definition
2020-01-14 15:24:43 +02:00
d86fbb2a08
adi_board: fixed ddr memory mapping for microblaze projects
2020-01-13 12:25:23 +02:00
34ea5efdff
adi_project_xilinx: Use the latest board files
2020-01-13 12:25:23 +02:00
Laszlo Nagy
Istvan Csomortani
Adrian Costina
AndreiGrozav
Stanca Pop
sarpadi
StancaPop
sraus