Expose the TX configurable driver ports, more specifically the
TX_DIFFCTRL, TX_POSTCURSORE and TX_PRECURSORE for software. This
provides a soft tunning capability of the transmit side of the
transceivers, in cases where the insertion loss of the channel is too
high or low, comparing to the default value supported by the default
configuration of the GTs.
You can find information about these configuration ports under the
section called 'TX Configurable Driver' in the GT transceivers user
guide. (UG476, UG576)
This commit does not contain any functional modification.
Because the wizard generates the attributes in binary, we should use
binary mode too, so we can compare different configurations more easily.
The Xilinx's reset interface expect that every reset have an associated
interface and clock signal. The tool will try to find its clock and interface,
and automatically associated clock signal to it.
The PLL resets are individual asynchronous resets. To simplify the design
and avoid invalid critical warnings all the reset interface inference
for the PLL resets were removed.
For a proper reset synchronization, the asynchronous reset signal should
be connected to the reset pins of the two synchronizer flop, and the
data input of the first flop should be connected to VCC.
In the first stage we're synchronizing just the reset de-assertion, avoiding
the scenario when different parts of the design are reseting at different time,
causing unwanted behaviours.
In the second stage we're synchronizing the reset assertion.
The module expects an ACTIVE_HIGH input reset signal, and provides an ACTIVE_LOW
(rstn) and an ACTIVE_HIGH (rst) synchronized reset output signal.
Fix the read side of the CDC data FIFO. The read address generation did not
function correctly.
Redesign the read side of the FIFO, and make sure that it becomes empty after
the DMA transfer ends; and never get stock in a cyclic mode.
The dac_last signal is not used anywhere in the module. Remove it and its
synchronization registers.
Fixes the following warnings:
[Synth 8-6014] Unused sequential element dac_dlast_reg was removed. ["axi_dacfifo_rd.v":372]
[Synth 8-6014] Unused sequential element dac_dlast_m1_reg was removed. ["axi_dacfifo_rd.v":373]
[Synth 8-6014] Unused sequential element dac_dlast_m2_reg was removed. ["axi_dacfifo_rd.v":374]
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Commit bfc8ec28c3 ("util_axis_fifo: instantiate block ram in async mode")
added the read-enable (reb) signal to the ad_mem block.
It didn't update the ad_mem instance in axi_dacfifo_address_buffer.v. This
results in the read-enable of the address_buffer being tied to 0.
Fix this by connecting the same signal that increments the read address.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Some designs choose to swap the positive and negative side of the of the
JESD204 lanes. One reason for this would be because it can simplify the
PCB layout. The polarity is in most cases also only applied to a subset of
the used lanes.
Add support for this to the util_adxcvr module. This done by adding new
parameter to the modules that allows to specify a per lane polarity
inversion. Each bit in the parameter corresponds to one lane. If the bit is
set the polarity is inverted for his lane. E.g. setting the parameter to
0xc will invert the 3rd and 4th lane.
The setting is forwarded to the Xilinx transceiver for the corresponding
lane.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Currently the individual IP core dependencies are tracked inside the
library Makefile for Xilinx IPs and the project Makefiles only reference
the IP cores.
For Altera on the other hand the individual dependencies are tracked inside
the project Makefile. This leads to a lot of duplicated lists and also
means that the project Makefiles need to be regenerated when one of the IP
cores changes their files.
Change the Altera projects to a similar scheme than the Xilinx projects.
The projects themselves only reference the library as a whole as their
dependency while the library Makefile references the individual source
dependencies.
Since on Altera there is no target that has to be generated create a dummy
target called ".timestamp_altera" who's only purpose is to have a timestamp
that is greater or equal to the timestamp of all of the IP core files. This
means the project Makefile can have a dependency on this file and make sure
that the project will be rebuild if any of the files in the library
changes.
This patch contains quite a bit of churn, but hopefully it reduces the
amount of churn in the future when modifying Altera IP cores.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The DC filter implementation in library/common/dc_filter.v is Xilinx
specific as it uses the Xilinx DSP48 hard-macro. There is a matching Altera
specific implementation in library/altera/common/dc_filter.v.
Move the Xilinx specific implementation from the generic common folder to
the Xilinx specific common folder in library/xilinx/common/ since that is
where all other Xilinx specific common modules reside.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
This reduces the amount of boilerplate code that is present in these
Makefiles by a lot.
It also makes it possible to update the Makefile rules in future without
having to re-generate all the Makefiles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
In cases when a shallow FIFO is requested the synthesizer infers distributed RAM
instead of block RAMs. This can be an issue when the clocks of the FIFO are
asynchronous since a timing path is created though the LUTs which implement the
memory, resulting in timing failures. Ignoring timing through the path is not a
solution since would lead to metastability.
This does not happens with block RAMs.
The solution is to use the ad_mem (block RAM) in case of async clocks and letting
the synthesizer do it's job in case of sync clocks for optimal resource utilization.
The up_rstn is driven by s_axi_resetn, which is generated by a
Processor System Reset module. (connected to port peripheral_aresetn)
Therefor using this reset signal as an asynchronous reset is redundant,
and a bad design practice at the same time. Asynchronous reset should be
used if it's inevitable.
The util_adxcvr supports GTX2, GTH3 and GTH4. The transceiver is selected
using the XCVR_TYPE parameter.
The axi_adxcvr on the other hand only has a configuration parameter to
indicate whether a GTX or GTH transceiver is used (GTH_OR_GTX_N). Since
there are some minor differences between GTH3 and GTH4 that software needs
to know about rename the GTH_OR_GTX_N to XCVR_TYPE and match use the same
semantics as util_adxcvr.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Add missing timing exceptions on paths between the DMA and DDR clock
domains. All these paths are properly synchronized using CDC in the HDL,
but are missing timing exceptions in the XDC file. This can lead to timing
errors when building a design using the axi_adc_fifo.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Adrian Costina
AndreiGrozav
Istvan Csomortani
Lars-Peter Clausen
Laszlo Nagy