Export the reset signal for the link clock domain. This can be used by
external logic that is in the link clock domain to reset itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Enabling the phase alignment mode of the FPLL seems to break manual
re-calibration, which is required when changing the lane rates. The
calibration seems to select the wrong VCO frequency band and the PLL no
longer locks.
Disable phase alignment mode for now, this has a negative effects on
deterministic latency, but it is better than not working at all.
Waiting for feedback from Altera/Intel on how to make manual re-calibration
work in phase alignment mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
To be able to check the FPLL re-configuration arbitration status from
software enable the avmm_busy flag in the register map.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The DEGLITCH state of the RX state machine is a workaround for misbehaving
PHYs. It is an internal state and an implementation detail and it does not
really make sense to report through the status interface.
Rework things so that DEGLITCH state is reported as part of the CGS state
on the external status interface.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The current layout of the debug ID register assumes that the ID_WIDTH is 3.
Change things so that the padding 0 width depends on the ID_WIDTH
parameter so that we end up with the same register layout regardless of the
value of ID_WIDTH.
Also split things into two registers, this allows for an ID_WIDTH up to 8
(which should hopefully be enough for all practical applications).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Redesign the axi_dacfifo, to increase the supported datarates.
Major modifications:
+ The FIFO consist of two module: WRITE and READ. The axi_dacfifo_dac
was deprecated.
+ Both the AXI write and AXI read transaction are controlled by two
FSM, to increase redability of the code.
+ Support all the possible burst lengths [0..225], handles the last
fractional burst on both sides correctly.
+ Common reset architecture throughout the design, all the internal
registers and memories are reset on the posedge of dma_xfer_req
+ Delete all Altera related sources, for Altera projects
avl_dacfifo should be used.
WIP: foobar
[WIP]axi_dacfifo: Update
axi_dacfifo: Few minor updates, almost working state
Add support for the AD-FMCDAQ2-EBZ on the Arria10 SoC development board platform.
In its default configuration the Arria10 SoC development board is not fully
compatible with the AD-FMCDAQ2-EBZ and a slight rework is necessary,
changing the position of four 0 Ohm resistors:
R610: DNI -> R0
R611: DNI -> R0
R612: R0 -> DNI
R613: R0 -> DNI
R620: DNI -> R0
R632: DNI -> R0
R621: R0 -> DNI
R633: R0 -> DNI
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Rework the peripheral address to match the updated semantics of
ad_cpu_interconnect, which expects that the addresses are in the range of
0x00010000 - 0x001fffff. This includes updating the base addresses as well
as compressing the used address range to fit into the 2Mb window.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Add a wrapper module for Altera/Intel platforms that instantiates and
connects all the components required to for a JESD204 link.
The following components are created:
* Transceiver for each lane
* Transceiver lane PLL (TX only)
* Transceiver reset controller
* Link PLL
* JESD204 link layer processing
* JESD204 link layer processing control interface
* axi_adxcvr link management peripheral
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Add a wrapper that instantiates the Arria10 Native PHY and configures it
for JESD204 operation. The datapath width is set to 4 octets per beat.
The maximum lane rate that is achievable with hard-logic PCS included in
the PHY is below the requirements of the JESD204 for some of the PHY speed
grades. For projects that require a lane rate that is higher than what the
hard-logic PCS can support a soft-logic PCS module can be instantiated. The
external interface of the jesd204_phy is identical regardless of whether
soft- or hard-logic PCS is used.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Add soft logic PCS that performs 8b10b encoding for TX and character
pattern alignment and 8b10b decoding for RX.
The modules are intended to be used in combination with a transceiver that
does not have these features implemented in hard logic PCS.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Add Qsys IP scripts as well as SDC constraint files for the ADI JESD204
peripherals. This allows them to be instantiated and used on Altera/Intel
platforms.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The Xilinx tools are quite forgiving when it comes to required signals on
standard interfaces, which is why it was possible to define a AXI streaming
interface without the required valid signal.
The Altera tools are more strict and wont allow this. Add a dummy valid
signal to the TX data interface to make the tools happy. For now the signal
does not do anything, in the future it might be used to detect an underflow
condition on the data interface and report this through the status
interface.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Currently the ILAS memory for the receive register map uses a shift
register with variable tap output for storing the ILAS information. This
maps very efficiently onto the primitives found in Xilinx FPGAs. But there
is no equivalent primitive in Altera FPAGs resulting in increased
utilization from having to implement the structure in pure logic.
Change the ILAS memory so it uses a simple dual port RAM for storing the
data. This has slightly increased utilization on Xilinx platforms (but
still good enough) and highly decreased utilization on Altera platforms.
One side effect of this change is that since the RAM output is synchronous
reading the ILAS memory registers will take one extra clock cycle.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Add a set of helper functions for the CDC library that creates the correct
constraints for the CDC blocks. This makes it easier to specify the
constraints in the individual user's SDC files.
This only works for Altera where full scripting capabilities are available
in the SDC files.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Allow to specify additional properties when defining a IP parameter. The
properties take the form of a list of key value pairs. E.g.
ad_ip_parameter ... { \
DISPLAY_NAME "Name" \
DISPLAY_HINT "radio" \
}
This helps to reduce the amount of boilerplate when additional properties
need to be specified for a parameter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
TCL files can be helpful to automate certain tasks like creating timing
constraints. Add handling for them to the ad_ip_addfile function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Currently the reset for the link clock domain is generated internally in
the axi_jesd204_{rx,tx} peripheral. The reset is controlled by through the
register map.
Add an additional external reset for link clock domain. The link clock
domain is kept in reset if either the internal reset or the external reset
is asserted.
This for example allows the fabric to keep the domain in reset if the clock
is not yet stable.
The status of the external reset can be queried from the register map.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
dma_raddr is only incremented if it is less than dma_waddr_rel_s.
dma_waddr_rel_s is always less or equal to adc_waddr_rel << RATIO and
adc_waddr_rel is less than DMA_ADDR_LIMIT >> RATIO.
By induction we can conclude that this means that dma_raddr will always be
less then DMA_ADDR_LIMIT and the check for this will always evaluate to
false can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
When the DMA clock to ADC data rate ratio exceeds a certain threshold it is
possible that an erroneous dma_waddr_rel toggle event is generated. This
causes the last address of the previous DMA transfer to be transferred to
the DMA domain. And the DMA side will start reading from the FIFO even
though data is not available yet.
This results in data corruption with the current transfer containing data
from the previous transfer.
The root cause here is that the toggle signal CDC synchronizer register are
reset in the DMA when a new transfer starts, but not in the ADC domain,
causing a potential mismatch and the incorrect toggle event. To fix this
remove the reset from the DMA side. This is OK since the registers are
self-resetting if the reset signal is asserted for more than 3 clock cycles.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
AND logic means that all enabled triggers need to evaluate to true, others
are don't care. Fix the logic to behave accordingly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
At the moment the drain signal is always asserted when the controller is
enabled. This breaks backpressure and data is lost. The drain signal should
only be asserted when the controller gets disabled until the last beat of
the current DMA transfer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The 'PRIMITIVE_SUBGROUP == flop' filter only works on 7-Series. Replace it
with 'IS_SEQUENTIAL' which works on both 7-Series and UltraScale.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
In its default configuration the ram_2port module as a read latency of 2
clock cycles. Both the read address as well as the output data are
registered.
This is not the behavior that is expected from the alt_mem_asym module and
causes incorrect behavior and data corruption in the util_adc_fifo.
Disable the data output register to get a read latency of 1 clock cycle.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Adrian Costina
Lars-Peter Clausen
Rejeesh Kutty
AndreiGrozav
Istvan Csomortani