- removed the delay controller from the top file and added it inside the util_gmii_to_rgmii core
- removed delay related xdc constraints as they are not needed
Since we are just doing a loopback all the logic is contained within the
IO bank. By using a BUFIO instead of a BUFG we avoid having to route the
clock signal from the IO bank to the middle of the FPGA and back to the IO
bank. This reduces the skew between clock and the data signals and makes
sure that the we can use the same design over a range of different
resolutions without having to calibrate the delay.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The ADV7511 samples on the rising edge. Update the data on the falling
edge, this gives us a larger margin and improved signal stability.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Since we are just doing a loopback all the logic is contained within the
IO bank. By using a BUFIO instead of a BUFG we avoid having to route the
clock signal from the IO bank to the middle of the FPGA and back to the IO
bank. This reduces the skew between clock and the data signals and makes
sure that the we can use the same design over a range of different
resolutions without having to calibrate the delay.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The ADV7511 samples on the rising edge. Update the data on the falling
edge, this gives us a larger margin and improved signal stability.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Those were added by mistake. It does not seem to be legal Verilog, but for
some reason Vivado accepts it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
ffff and 0000 are always reserved control characters when using embedded
syncs. So make sure that we never have them in the pixel data, even when
running in full-range mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Add a control bit to the register map that allows to bypass the chroma
sub-sampler in the axi_hdmi_tx core. This is primarily interned to be used
to send the test-pattern directly to the HDMI transmitter without modifying
it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Connect the raw HDMI data as generated by the ADV7604 to the ILA. For
debugging it is quite useful to be able to compare the data before and
after conversion pipeline.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Currently the hdmi_de_int signal is asserted one clock cycle too early in
packed 422 mode. As a result the EAV sequence ends up in the first pixel
and every other pixel is off by one.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Check for both full range and limited range test-pattern sequences and only
if both don't match assert the tpm_oos signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Move the test pattern matcher to its own module. This makes it easier to
use it in other configurations as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The TPG is no longer part of the RX core and the corresponding bit in the
register map isn't hooked up to anything. So drop it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The TPM OOS status flag is in bit 1. Make sure writing to bit 1 rather than
bit 0 clears the TPM OOS.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Add .gitattributes file which sets up the eol encoding handling. This will
make sure that we get a uniform eol encoding across different operating
systems.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Rejeesh Kutty
Adrian Costina
Istvan Csomortani
Lars-Peter Clausen