Running 'make' will build the default project directly in the project folder (like it did before)
Running 'make RX_LANE_RATE=15 TX_LANE_RATE=15' will build the project inside the 'RXRATE15_TXRATE15' subdirectory.
Running 'make CFG=cfg/test_config.txt" will use the variables found inside the configuration file and build the project inside the 'test_config' subdirectory.
Running 'make clean' will clean the default project only.
Running 'make CFG=cfg/test_config.txt clean' will clean the 'testconfig' build.
Running 'make clean-all' will delete all the built configurations and libraries.
Note that the 'JESD' and 'LANE' words from the parameter names are stripped.
Signed-off-by: Bogdan Luncan <bogdan.luncan@analog.com>
In ad_xcvrcon procedure from adi_board, phy_en_char_align must be connected only when 8B10B encoding is used,
otherwise this signal does not exists in the JESD ip and will cause an error.
Signed-off-by: Filip Gherman <Filip.Gherman@analog.com>
New improvements for the ADI DMAC IP:
1)The capability to manually overwrite the DMA_AXI_ADDR_WIDTH(from GUI or from tcl)
2)DMA_AXI_ADDR_WIDTH attribute is now visible in the Vivado GUI:
-"Auto mode": Automatically calculated by the core tcl files based on the existing attached address segments.
-"Manual mode": Specify the desired dma_width between 32-64 bits.
3)Added two new debug registers that return higher part of the current source/destination address.
Signed-off-by: Filip Gherman <Filip.Gherman@analog.com>
If 'xvlog' or 'xelab' xilinx commands are failing, exit from
run_tb.sh script without trying to run simulation.
Signed-off-by: stefan.raus <stefan.raus@analog.com>
Expose JESD parameters to make.
Add FMCOMMS8 parameter.
Changed the name of the observation path to match the rest of the repo.
Replace old dac_data_width formula with a more generic one.
Update clean command to delete also files generated by simulation,
from 'tb' folders, covering cases for Xsim and ModelSim simulators.
Signed-off-by: stefan.raus <stefan.raus@analog.com>
* Before, adc_valid was for the previous sample. This said that
at the second rising edge of clk_gate - the first sample is valid,
which is not true
* Alongside with the software issue that will be solved, these fixes
will make the first 2 samples to be with valid data, otherwise the
user has to always keep in mind that the first 2 ones are invalid
Signed-off-by: Iulia Moldovan <iulia.moldovan@analog.com>
* Update xdc to use diff_term true instead of diff_term 1
* Generated xdc using adi_fmc_constr_generator.tcl
* Make CSN to be inactive
* Cosmetic changes also
Signed-off-by: Iulia Moldovan <iulia.moldovan@analog.com>
Using the script:
- make sure that the eval board in use has a common fmc connection file.
if you created a new one, it should be saved as &project_name_fmc.txt inside
&project_name/common
- open a tcl terminal, either inside or outside the project
- make sure your current directory is &hdl_repo/projects/&project_name/&carrier
- source the script found at &hdl_repo/project/scripts/fmc_constr_generator.tcl
- call gen_fmc_constr $parameter_1 $parameter_2:
- in case of only one fmc port on the carrier call without any parameters
- if there are two fmc ports on the carrier and you want to use only one,
the first parameter should contain an indication (fmc_lpc/hpc, fmc0/1, etc.)
- if there are two fmc ports on the carrier and you want to use both, then
both parameters should contain an indication
- the constraints file will be generated in the current directory
Signed-off-by: AndrDragomir <andrei.dragomir@analog.com>
AndrDragomir
Sergiu Arpadi
PopPaul2021
Bogdan Luncan
Filip Gherman
Travis F. Collins
alin724
Laszlo Nagy
AndreiGrozav
laurent-19
Liviu.Iacob
PopPaul2021
Iulia Moldovan
stefan.raus
Stanca Pop
Ionut Podgoreanu