diff --git a/library/altera/common/ad_serdes_clk.v b/library/altera/common/ad_serdes_clk.v
index 2ed1b58f5..e708404f2 100644
--- a/library/altera/common/ad_serdes_clk.v
+++ b/library/altera/common/ad_serdes_clk.v
@@ -191,7 +191,7 @@ module __ad_serdes_clk__ #(
     .pll_reconfig_read (up_drp_rd_int),
     .pll_reconfig_write (up_drp_wr_int),
     .pll_reconfig_readdata (up_drp_rdata_int_s),
-    .pll_reconfig_address (up_drp_addr_int),
+    .pll_reconfig_address (up_drp_addr_int[5:0]),
     .pll_reconfig_writedata (up_drp_wdata_int));
 
   cyclonev_pll_lvds_output #(
diff --git a/library/altera/common/ad_serdes_in.v b/library/altera/common/ad_serdes_in.v
index abadf7bae..9b147d698 100644
--- a/library/altera/common/ad_serdes_in.v
+++ b/library/altera/common/ad_serdes_in.v
@@ -136,89 +136,17 @@ module __ad_serdes_in__ #(
   for (n = 0; n < DATA_WIDTH; n = n + 1) begin: g_data
 
   if (DEVICE_TYPE == CYCLONE5) begin
-  altlvds_rx #(
-    .buffer_implementation ("RAM"),
-    .cds_mode ("UNUSED"),
-    .common_rx_tx_pll ("ON"),
-    .data_align_rollover (4),
-    .data_rate ("500.0 Mbps"),
-    .deserialization_factor (4),
-    .dpa_initial_phase_value (0),
-    .dpll_lock_count (0),
-    .dpll_lock_window (0),
-    .enable_clock_pin_mode ("UNUSED"),
-    .enable_dpa_align_to_rising_edge_only ("OFF"),
-    .enable_dpa_calibration ("ON"),
-    .enable_dpa_fifo ("UNUSED"),
-    .enable_dpa_initial_phase_selection ("OFF"),
-    .enable_dpa_mode ("OFF"),
-    .enable_dpa_pll_calibration ("OFF"),
-    .enable_soft_cdr_mode ("OFF"),
-    .implement_in_les ("OFF"),
-    .inclock_boost (0),
-    .inclock_data_alignment ("EDGE_ALIGNED"),
-    .inclock_period (4000),
-    .inclock_phase_shift (0),
-    .input_data_rate (500),
-    .intended_device_family ("Cyclone V"),
-    .lose_lock_on_one_change ("UNUSED"),
-    .lpm_hint ("CBX_MODULE_PREFIX=ad_serdes_in"),
-    .lpm_type ("altlvds_rx"),
-    .number_of_channels (DATA_WIDTH),
-    .outclock_resource ("Regional clock"),
-    .pll_operation_mode ("NORMAL"),
-    .pll_self_reset_on_loss_lock ("UNUSED"),
-    .port_rx_channel_data_align ("PORT_UNUSED"),
-    .port_rx_data_align ("PORT_UNUSED"),
-    .refclk_frequency ("250.000000 MHz"),
-    .registered_data_align_input ("UNUSED"),
-    .registered_output ("ON"),
-    .reset_fifo_at_first_lock ("UNUSED"),
-    .rx_align_data_reg ("RISING_EDGE"),
-    .sim_dpa_is_negative_ppm_drift ("OFF"),
-    .sim_dpa_net_ppm_variation (0),
-    .sim_dpa_output_clock_phase_shift (0),
-    .use_coreclock_input ("OFF"),
-    .use_dpll_rawperror ("OFF"),
-    .use_external_pll ("ON"),
-    .use_no_phase_shift ("ON"),
-    .x_on_bitslip ("ON"),
-    .clk_src_is_pll ("off"))
-  i_altlvds_rx (
-    .rx_inclock (clk),
-    .rx_in (data_in_p[n]),
-    .rx_outclock (),
-    .rx_out (data_out_s[n]),
-    .rx_locked (),
-    .dpa_pll_cal_busy (),
-    .dpa_pll_recal (1'b0),
-    .pll_areset (~locked),
-    .pll_phasecounterselect (),
-    .pll_phasedone (1'b1),
-    .pll_phasestep (),
-    .pll_phaseupdown (),
-    .pll_scanclk (),
-    .rx_cda_max (),
-    .rx_cda_reset ({7{1'b0}}),
-    .rx_channel_data_align ({7{1'b0}}),
-    .rx_coreclk (1'b1),
-    .rx_data_align (1'b0),
-    .rx_data_align_reset (1'b0),
-    .rx_data_reset (1'b0),
-    .rx_deskew (1'b0),
-    .rx_divfwdclk (),
-    .rx_dpa_lock_reset ({7{1'b0}}),
-    .rx_dpa_locked (),
-    .rx_dpaclock (1'b0),
-    .rx_dpll_enable ({7{1'b1}}),
-    .rx_dpll_hold ({7{1'b0}}),
-    .rx_dpll_reset ({7{1'b0}}),
-    .rx_enable (loaden),
-    .rx_fifo_reset ({7{1'b0}}),
-    .rx_pll_enable (1'b1),
-    .rx_readclock (1'b0),
-    .rx_reset ({7{1'b0}}),
-    .rx_syncclock (1'b0));
+
+  assign delay_locked_s[n] = 1'b1;
+
+  ad_serdes_in_core_c5 #(
+    .SERDES_FACTOR (SERDES_FACTOR))
+  i_core (
+    .clk (clk),
+    .div_clk (div_clk),
+    .enable (loaden),
+    .data_in (data_in_p[n]),
+    .data (data_out_s[n]));
   end
 
   if (DEVICE_TYPE == ARRIA10) begin
diff --git a/library/altera/common/ad_serdes_out.v b/library/altera/common/ad_serdes_out.v
index 47298a0dc..8bca8ffd5 100644
--- a/library/altera/common/ad_serdes_out.v
+++ b/library/altera/common/ad_serdes_out.v
@@ -109,53 +109,14 @@ module __ad_serdes_out__ #(
   for (n = 0; n < DATA_WIDTH; n = n + 1) begin: g_data
 
   if (DEVICE_TYPE == CYCLONE5) begin
-  altlvds_tx #(
-    .center_align_msb ("UNUSED"),
-    .common_rx_tx_pll ("ON"),
-    .coreclock_divide_by (1),
-    .data_rate ("500.0 Mbps"),
-    .deserialization_factor (4),
-    .differential_drive (0),
-    .enable_clock_pin_mode ("UNUSED"),
-    .implement_in_les ("OFF"),
-    .inclock_boost (0),
-    .inclock_data_alignment ("EDGE_ALIGNED"),
-    .inclock_period (4000),
-    .inclock_phase_shift (0),
-    .intended_device_family ("Cyclone V"),
-    .lpm_hint ("CBX_MODULE_PREFIX=ad_serdes_out"),
-    .lpm_type ("altlvds_tx"),
-    .multi_clock ("OFF"),
-    .number_of_channels (DATA_WIDTH),
-    .outclock_alignment ("EDGE_ALIGNED"),
-    .outclock_divide_by (2),
-    .outclock_duty_cycle (50),
-    .outclock_multiply_by (1),
-    .outclock_phase_shift (0),
-    .outclock_resource ("Regional clock"),
-    .output_data_rate (500),
-    .pll_compensation_mode ("AUTO"),
-    .pll_self_reset_on_loss_lock ("OFF"),
-    .preemphasis_setting (0),
-    .refclk_frequency ("250.000000 MHz"),
-    .registered_input ("TX_CORECLK"),
-    .use_external_pll ("ON"),
-    .use_no_phase_shift ("ON"),
-    .vod_setting (0),
-    .clk_src_is_pll ("off"))
-  i_altlvds_tx (
-    .tx_inclock (clk),
-    .tx_coreclock (div_clk),
-    .tx_in (data_in_s[n]),
-    .tx_outclock (),
-    .tx_out (data_out_p[n]),
-    .tx_locked (),
-    .pll_areset (1'b0),
-    .sync_inclock (1'b0),
-    .tx_data_reset (1'b0),
-    .tx_enable (loaden),
-    .tx_pll_enable (1'b1),
-    .tx_syncclock (1'b0));
+  ad_serdes_out_core_c5 #(
+    .SERDES_FACTOR (SERDES_FACTOR))
+  i_core (
+    .clk (clk),
+    .div_clk (div_clk),
+    .enable (loaden),
+    .data_out (data_out_p[n]),
+    .data (data_in_s[n]));
   end
 
   if (DEVICE_TYPE == ARRIA10) begin
diff --git a/library/axi_ad9361/altera/axi_ad9361_lvds_if.v b/library/axi_ad9361/altera/axi_ad9361_lvds_if.v
index e3940d312..1763d272b 100644
--- a/library/axi_ad9361/altera/axi_ad9361_lvds_if.v
+++ b/library/axi_ad9361/altera/axi_ad9361_lvds_if.v
@@ -436,8 +436,8 @@ module axi_ad9361_lvds_if #(
     .data_in_p (rx_frame_in_p),
     .data_in_n (rx_frame_in_n),
     .up_clk (1'd0),
-    .up_dld (6'd0),
-    .up_dwdata (30'd0),
+    .up_dld (1'd0),
+    .up_dwdata (5'd0),
     .up_drdata (),
     .delay_clk (1'd0),
     .delay_rst (1'd0),
diff --git a/library/scripts/adi_ip_alt.tcl b/library/scripts/adi_ip_alt.tcl
index a26b5336d..c1db04ff4 100644
--- a/library/scripts/adi_ip_alt.tcl
+++ b/library/scripts/adi_ip_alt.tcl
@@ -89,6 +89,41 @@ proc ad_generate_module_inst { inst_name mark source_file target_file } {
   close $fp_target
 }
 
+proc ad_ip_parameter {pname ptype pdefault} {
+
+  add_parameter $pname $ptype $pdefault
+  set_parameter_property $pname HDL_PARAMETER true
+  set_parameter_property $pname ENABLED true
+}
+
+proc ad_ip_files {pname pfiles {pfunction ""}} {
+
+  set ftopfile [lindex $pfiles end]
+  set pfiles [lreplace $pfiles end end]
+
+  add_fileset quartus_synth QUARTUS_SYNTH $pfunction ""
+  set_fileset_property quartus_synth TOP_LEVEL $pname
+
+  foreach pfile $pfiles {
+    set pmodule [file tail $pfile]
+    add_fileset_file $pmodule VERILOG PATH $pfile
+  }
+  set pfile $ftopfile
+  set pmodule [file tail $pfile]
+  add_fileset_file $pmodule VERILOG PATH $pfile TOP_LEVEL_FILE
+
+  add_fileset quartus_sim SIM_VERILOG $pfunction ""
+  set_fileset_property quartus_sim TOP_LEVEL $pname
+
+  foreach pfile $pfiles {
+    set pmodule [file tail $pfile]
+    add_fileset_file $pmodule VERILOG PATH $pfile
+  }
+  set pfile $ftopfile
+  set pmodule [file tail $pfile]
+  add_fileset_file $pmodule VERILOG PATH $pfile TOP_LEVEL_FILE
+}
+
 proc ad_ip_intf_s_axi {aclk arstn} {
 
   add_interface s_axi_clock clock end