zcy
/
pluto_hdl_adi
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
pluto_hdl_adi/projects/dac_fmc_ebz/zcu102/system_bd.tcl

39 lines
1.7 KiB
Tcl
Raw Normal View History

dac_fmc_ebz: Add initial ZCU102 and ZC706 carrier support Add a generic project for the AD91xx-FMC-EBZ DAC boards connected to the ZCU102 and ZC706 carrier boards. The project is called dac_fmc_ebz as the intention is to support all DAC FMC evaluation boards with this project since they are sufficiently similar to be supported by the same design. This project will successively extended to add support for more boards. The desired DAC device and JESD operation mode must be selected from the following file: ./common/config.tcl This design can support the following FMC boards which are all pin compatible: * AD9135-FMC-EBZ * AD9136-FMC-EBZ * AD9144-FMC-EBZ * AD9152-FMC-EBZ * AD9154-FMC-EBZ * AD916x-FMC-EBZ * AD9171-FMC-EBZ * AD9172-FMC-EBZ * AD9173-FMC-EBZ Note that the AD9152-FMC-EBZ only uses the first 4 lanes, whereas all other boards use 8 lanes. This project assumes that the transceiver reference clock and SYSREF are provided via the clock distribution chip that is found on the ADxxxx-FMC-EBZ board. In terms of pin connections between the FPGA and the FMC board the AD9172-FMC-EBZ is very similar to the AD9144-FMC-EBZ. The main differences are: * The DAC txen signals are connected to different pins * The polarity of the spi_en signal is active low instead of active high * The maximum lane rate is up to 15.4 Gpbs To accommodate this 5 txctrl signals as well as the spi_en signal are connected to GPIOs. Software can decide how to use them depending on which FMC board is connected. Note that each carrier has a maximum supported lane rate. Modes of the AD9172 (and similar) that exceed the carrier specific limit can not be used on that carrier. The limits are as following: * ZC706: 10.3125 Gbps * ZCU102: 15.4 Gbps (max AD9172 lanerate) * SPI and GPIOs to PMOD header support Connect a SPI interface and some GPIOs to the PL PMOD headers on the zcu102 and zc706 carriers. This is can be used to control additional external hardware like a clock chip or an analog front-end. This is especially useful on FMC boards that do not feature a clock generator chip. The pin out is: PMOD 1: SPI clock PMOD 2: SPI chipselect PMOD 3: SPI MOSI PMOD 4: SPI MISO PMOD 7: GPIO 0 PMOD 8: GPIO 1 PMOD 9: GPIO 2 PMOD 10: GPIO 3 The GPIOs are mapped at offset 48-51 of the EMIO GPIOs.
2018-06-15 11:50:34 +00:00
set dac_fifo_address_width 13
source $ad_hdl_dir/projects/common/zcu102/zcu102_system_bd.tcl
source $ad_hdl_dir/projects/common/xilinx/dacfifo_bd.tcl
source ../common/dac_fmc_ebz_bd.tcl
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.QPLL_REFCLK_DIV 1
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.QPLL_CFG2 0xFC0
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.QPLL_CFG3 0x120
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.QPLL_CFG0 0x333C
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.QPLL_FBDIV 40
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.QPLL_CFG4 0x45
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.QPLL_CFG1 0xD038
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.QPLL_CFG1_G3 0xD038
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.QPLL_CFG2_G3 0xFC0
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.TX_CLK25_DIV 15
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.TX_OUT_DIV 1
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.TXPI_CFG 0x0
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.A_TXDIFFCTRL 0xC
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.TX_PI_BIASSET 3
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.POR_CFG 0x0
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.PPF0_CFG 0xF00
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.QPLL_CP 0xFF
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.QPLL_CP_G3 0xF
ad_ip_parameter util_dac_jesd204_xcvr CONFIG.QPLL_LPF 0x31D
ad_ip_parameter dac_jesd204_link/tx CONFIG.SYSREF_IOB false
system_id: deployed ip
2019-06-28 08:41:21 +00:00
#system ID
ad_ip_parameter axi_sysid_0 CONFIG.ROM_ADDR_BITS 9
ad_ip_parameter rom_sys_0 CONFIG.PATH_TO_FILE "[pwd]/mem_init_sys.txt"
ad_ip_parameter rom_sys_0 CONFIG.ROM_ADDR_BITS 9
dac_fmc_ebz: Add project info to sys_id Add project device and mode info to sys_id custom string
2019-10-10 13:05:47 +00:00
set ADI_DAC_DEVICE $::env(ADI_DAC_DEVICE)
set ADI_DAC_MODE $::env(ADI_DAC_MODE)
set sys_cstring "$ADI_DAC_DEVICE - $ADI_DAC_MODE"
system_id: deployed ip
2019-06-28 08:41:21 +00:00
sysid_gen_sys_init_file $sys_cstring