diff --git a/arduino/arduino/moveo_moveit/move_moveit/move_moveit.ino b/arduino/arduino/moveo_moveit/move_moveit/move_moveit.ino
new file mode 100644
index 0000000..7519372
--- /dev/null
+++ b/arduino/arduino/moveo_moveit/move_moveit/move_moveit.ino
@@ -0,0 +1,154 @@
+/* Purpose: This sketch uses ROS as well as MultiStepper, AccelStepper, and Servo libraries to control the 
+ * BCN3D Moveo robotic arm. In this setup, a Ramps 1.4 shield is used on top of an Arduino Mega 2560.  
+ * Subscribing to the following ROS topics: 1) joint_steps, 2) gripper_angle
+ *    1) joint_steps is computed from the simulation in PC and sent Arduino via rosserial.  It contains
+ *       the steps (relative to the starting position) necessary for each motor to move to reach the goal position.
+ *    2) gripper_angle contains the necessary gripper angle to grasp the object when the goal state is reached 
+ * 
+ * Publishing to the following ROS topics: joint_steps_feedback
+ *    1) joint_steps_feedback is a topic used for debugging to make sure the Arduino is receiving the joint_steps data
+ *       accurately
+ *       
+ * Author: Jesse Weisberg
+ */
+#if (ARDUINO >= 100)
+  #include <Arduino.h>
+#else
+  #include <WProgram.h>
+#endif
+#include <ros.h>
+
+#include <moveo_moveit/ArmJointState.h>
+#include <Servo.h> 
+#include <std_msgs/Bool.h>
+#include <std_msgs/String.h>
+#include <math.h>
+#include <std_msgs/Int16.h>
+#include <std_msgs/UInt16.h>
+#include <AccelStepper.h>
+#include <MultiStepper.h>
+
+// Joint 1
+#define E1_STEP_PIN   53
+#define E1_DIR_PIN   51
+#define E1_ENABLE_PIN 31
+
+// Joint 2
+#define Z_STEP_PIN         32
+#define Z_DIR_PIN          30
+#define Z_ENABLE_PIN       62
+#define Z_MIN_PIN          18
+#define Z_MAX_PIN          19
+
+// Joint 3
+#define Y_STEP_PIN         48
+#define Y_DIR_PIN          46
+#define Y_ENABLE_PIN       56
+#define Y_MIN_PIN          14
+#define Y_MAX_PIN          15
+
+// Joint 4
+#define X_STEP_PIN 40
+#define X_DIR_PIN 42
+#define X_ENABLE_PIN 38
+
+// Joint 5 
+#define E0_STEP_PIN 43
+#define E0_DIR_PIN 41
+#define E0_ENABLE_PIN 24
+
+
+AccelStepper joint1(1,E1_STEP_PIN, E1_DIR_PIN);
+AccelStepper joint2(1,Z_STEP_PIN, Z_DIR_PIN);
+AccelStepper joint3(1,Y_STEP_PIN, Y_DIR_PIN);
+AccelStepper joint4(1,X_STEP_PIN, X_DIR_PIN);
+AccelStepper joint5(1, E0_STEP_PIN, E0_DIR_PIN);
+
+Servo gripper;
+MultiStepper steppers;
+
+int joint_step[6];
+int joint_status = 0;
+
+ros::NodeHandle nh;
+std_msgs::Int16 msg;
+
+//instantiate publisher (for debugging purposes)
+//ros::Publisher steps("joint_steps_feedback",&msg);
+
+void arm_cb(const moveo_moveit::ArmJointState& arm_steps){
+  joint_status = 1;
+  joint_step[0] = arm_steps.position1;
+  joint_step[1] = arm_steps.position2;
+  joint_step[2] = arm_steps.position3;
+  joint_step[3] = arm_steps.position4;
+  joint_step[4] = arm_steps.position5;
+  joint_step[5] = arm_steps.position6; //gripper position <0-180>
+}
+
+void gripper_cb( const std_msgs::UInt16& cmd_msg){
+  gripper.write(cmd_msg.data); // Set servo angle, should be from 0-180  
+  digitalWrite(13, HIGH-digitalRead(13));  // Toggle led  
+}
+
+//instantiate subscribers
+ros::Subscriber<moveo_moveit::ArmJointState> arm_sub("joint_steps",arm_cb); //subscribes to joint_steps on arm
+ros::Subscriber<std_msgs::UInt16> gripper_sub("gripper_angle", gripper_cb); //subscribes to gripper position
+//to publish from terminal: rostopic pub gripper_angle std_msgs/UInt16 <0-180>
+
+void setup() {
+  //put your setup code here, to run once:
+  //Serial.begin(57600);
+  pinMode(13,OUTPUT);
+  joint_status = 1;
+
+  nh.initNode();
+  nh.subscribe(arm_sub);
+  nh.subscribe(gripper_sub);
+  //nh.advertise(steps);
+
+  // Configure each stepper
+  joint1.setMaxSpeed(1500);
+  joint2.setMaxSpeed(750);
+  joint3.setMaxSpeed(2000);
+  joint4.setMaxSpeed(500);
+  joint5.setMaxSpeed(1000);
+
+  // Then give them to MultiStepper to manage
+  steppers.addStepper(joint1);
+  steppers.addStepper(joint2);
+  steppers.addStepper(joint3);
+  steppers.addStepper(joint4);
+  steppers.addStepper(joint5);
+
+  // Configure gripper servo
+  gripper.attach(11);
+  
+  digitalWrite(13, 1); //toggle led
+}
+
+void loop() {
+  if (joint_status == 1) // If command callback (arm_cb) is being called, execute stepper command
+  { 
+    long positions[5];  // Array of desired stepper positions must be long
+    positions[0] = joint_step[0]; // negated since the real robot rotates in the opposite direction as ROS
+    positions[1] = -joint_step[1]; 
+    positions[2] = joint_step[2]; 
+    positions[3] = joint_step[3]; 
+    positions[4] = -joint_step[4]; 
+
+    // Publish back to ros to check if everything's correct
+    //msg.data=positions[4];
+    //steps.publish(&msg);
+
+    steppers.moveTo(positions);
+    nh.spinOnce();
+    steppers.runSpeedToPosition(); // Blocks until all are in position
+    gripper.write(joint_step[5]);  // move gripper after manipulator reaches goal   
+  }
+  digitalWrite(13, HIGH-digitalRead(13)); //toggle led
+  joint_status = 0;
+  
+  nh.spinOnce();
+  delay(1);
+}